- 您現在的位置：買賣IC網 > PDF目錄382560 > STLC2411 (意法半導體) BLUETOOTH BASEBAND PDF資料下載
參數資料
| 型號： | STLC2411 |
| 廠商： | 意法半導體 |
| 英文描述： | BLUETOOTH BASEBAND |
| 中文描述： | 藍牙基帶 |
| 文件頁數： | 12/25頁 |
| 文件大?。?/td> | 216K |
| 代理商： | STLC2411 |
STLC2411
12/25
7
GENERAL SPECIFICATION
7.1 SYSTEM CLOCK
The STLC2411 works with a single clock provided on the XIN pin. The value of this external clock should
be any integer value from 12 … 33 MHz ±20ppm (overall).
7.1.1 SLOW CLOCK
The slow clock is used by the baseband as reference clock during the low power modes. The slow clock
requires an accuracy of ±250ppm (overall).
Several options are foreseen in order to adjust the STLC2411 behaviour according to the features of the
radio used:
– If the system clock (e.g. 13MHz) is not provided at all times (power consumption saving) and no slow
clock is provided by the system, a 32 kHz crystal must be used by the STLC2411 (default mode).
– If the system clock (e.g. 13MHz) is not provided at all times (power consumption saving) and the system
provides a slow clock at 32kHz or 3.2kHz, this signal is simply connected to the STLC2411 (lpo_clk_p).
– If the system clock (e.g. 13MHz) is provided at all times, the STLC2411 generates from the reference
clock an internal 32kHz clock. This mode is not an optimized mode for power consumption.
7.2 BOOT PROCEDURE
The boot code instructions are the first that ARM7TDMI executes after a HW reset. All the internal device's
registers are set to their default value.
There are 2 types of boot:
– External memory boot.
When boot pin is set to `1` (connected to VDD), the STLC2411 boots on its external memory
– UART download boot from ROM.
When boot pin is set to `0` (connected to GND), the STLC2411 boots on its internal ROM (needed to
download the new firmware in the external memory).
When booting on the internal ROM, the STLC2411 will monitor the UART interface for approximately 1.4
second. If there is no request for code downloading during this period, the ROM jumps to external memory.
7.3 CLOCK DETECTION
The STLC2411 has an automatic slow clock frequency detection (32kHz, 3.2kHz or none).
7.4 MASTER RESET
When the device's reset is held active (nreset is low), uart1_txd and uart2_txd are set to input state. When
the nreset returns high, the device starts to boot.
Remark: The device should be held in active reset for minimum 20ms in order to guarantee a complete
reset of the device.
7.5 INTERRUPTS/WAKE-UP
All GPIOs can be used both as external interrupt source and as wake-up source. In addition, the chip can
be woken-up by USB, uart1_rxd, uart2_rxd, int1, int2.
7.6 V1.2 detailed functionality - Extended SCO
User Perspective - Extended SCO
This function gives improved voice quality since it enables the possibility to retransmit lost or corrupted
voice packets in both directions.
相關PDF資料 |
PDF描述 |
|---|---|
| STLC2416 | BLUETOOTH BASEBAND WITH INTEGRATED FLASH |
| STLC60243 | DUAL CHANNEL ADSL LINE DRIVER |
| STLC7545 | Enhanced V.34 BIS Analog Front-End(單片模擬前端) |
| STLC7549 | Stereo Audio/MODEM/Telephony Codec(立體聲音頻/調制解調器/電話編解碼器) |
| STLVD210B | DIFFERENTIAL LVDS CLOCK DRIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| STLC2415 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:BLUETOOTH BASEBAND WITH INTEGRATED FLASH |
| STLC2416 | 制造商:STMicroelectronics 功能描述: |
| STLC2450 | 功能描述:射頻無線雜項 Eval Board STLC2450 RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel |
| STLC2500 | 制造商:STMicroelectronics 功能描述:BLUETOOTH CLS II 2.65V TO 2.85V 0.721MBPS 84TFBGA - Trays |
| STLC2500A | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Bluetooth Single Chip |
發布緊急采購，3分鐘左右您將得到回復。