參數資料
型號: ST7PLITE05Y0M3
廠商: STMICROELECTRONICS
元件分類: 微控制器/微處理器
英文描述: 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO16
封裝: 0.150 INCH, PLASTIC, SOP-16
文件頁數: 27/115頁
文件大?。?/td> 781K
代理商: ST7PLITE05Y0M3
ST7FLITE0
19/115
CPU REGISTERS (Cont’d)
CONDITION CODE REGISTER (CC)
Read/Write
Reset Value: 111x1xxx
The 8-bit Condition Code register contains the in-
terrupt mask and four flags representative of the
result of the instruction just executed. This register
can also be handled by the PUSH and POP in-
structions.
These bits can be individually tested and/or con-
trolled by specific instructions.
Bit 4 = H
Half carry.
This bit is set by hardware when a carry occurs be-
tween bits 3 and 4 of the ALU during an ADD or
ADC instruction. It is reset by hardware during the
same instructions.
0: No half carry has occurred.
1: A half carry has occurred.
This bit is tested using the JRH or JRNH instruc-
tion. The H bit is useful in BCD arithmetic subrou-
tines.
Bit 3 = I
Interrupt mask.
This bit is set by hardware when entering in inter-
rupt or by software to disable all interrupts except
the TRAP software interrupt. This bit is cleared by
software.
0: Interrupts are enabled.
1: Interrupts are disabled.
This bit is controlled by the RIM, SIM and IRET in-
structions and is tested by the JRM and JRNM in-
structions.
Note: Interrupts requested while I is set are
latched and can be processed when I is cleared.
By default an interrupt routine is not interruptable
because the I bit is set by hardware at the start of
the routine and reset by the IRET instruction at the
end of the routine. If the I bit is cleared by software
in the interrupt routine, pending interrupts are
serviced regardless of the priority level of the cur-
rent interrupt routine.
Bit 2 = N
Negative.
This bit is set and cleared by hardware. It is repre-
sentative of the result sign of the last arithmetic,
logical or data manipulation. It is a copy of the 7
th
bit of the result.
0: The result of the last operation is positive or null.
1: The result of the last operation is negative
(i.e. the most significant bit is a logic 1).
This bit is accessed by the JRMI and JRPL instruc-
tions.
Bit 1 = Z
Zero.
This bit is set and cleared by hardware. This bit in-
dicates that the result of the last arithmetic, logical
or data manipulation is zero.
0: The result of the last operation is different from
zero.
1: The result of the last operation is zero.
This bit is accessed by the JREQ and JRNE test
instructions.
Bit 0 = C
Carry/borrow.
This bit is set and cleared by hardware and soft-
ware. It indicates an overflow or an underflow has
occurred during the last arithmetic operation.
0: No overflow or underflow has occurred.
1: An overflow or underflow has occurred.
This bit is driven by the SCF and RCF instructions
and tested by the JRC and JRNC instructions. It is
also affected by the “bit test and branch”, shift and
rotate instructions.
70
111
H
I
N
Z
C
1
相關PDF資料
PDF描述
ST7PLITE05Y0B3 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDIP16
ST7FLITE09Y0B3 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDIP16
ST7PLU09MCTRE 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO8
ST7PLU05MAE 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO8
ST7PLU09MAE 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO8
相關代理商/技術參數
參數描述
ST7PLITE05Y0M6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI
ST7PLITE05Y0M6TR 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-bit microcontroller with single voltage Flash memory, data EEPROM, ADC, timers, SPI
ST7PLITE05Y0U6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-bit microcontroller with single voltage Flash memory, data EEPROM, ADC, timers, SPI
ST7PLITE05Y0U6TR 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-bit microcontroller with single voltage Flash memory, data EEPROM, ADC, timers, SPI
ST7PLITE09F0U6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MICROCONTROLLER WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, TIMERS, SPI