參數資料
型號: ST62T63C
廠商: 意法半導體
英文描述: 8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, SAFE RESET, AUTO-RELOAD TIMER, EEPROM AND SPI
中文描述: 8位檢察官辦公室/存儲器與阿微控制器/ D轉換器,安全復位,自動重加載定時器,EEPROM和的SPI
文件頁數: 27/86頁
文件大?。?/td> 559K
代理商: ST62T63C
27/86
27
ST62T53C/T60C/T63C ST62E60C
3.3 DIGITAL WATCHDOG
The digital Watchdog consists of a reloadable
downcounter timer which can be used to provide
controlled recovery from software upsets.
The Watchdog circuit generates a Resetwhen the
downcounter reaches zero. User software can
prevent this reset by reloading the counter, and
should therefore be written so that the counter is
regularly reloaded while the user program runs
correctly. Inthe event of a software mishap (usual-
ly caused by externally generated interference),
the user program will no longer behave in its usual
fashion and the timer register will thus not be re-
loaded periodically. Consequently the timer will
decrement down to 00h and reset the MCU. In or-
der to maximise the effectiveness of the Watchdog
function, user software must be written with this
concept in mind.
Watchdog behaviour is governed by two options,
known
as
“WATCHDOG
HARDWARE or SOFTWARE) and “EXTERNAL
STOP MODE CONTROL” (see Table 6).
In the SOFTWARE option, the Watchdog is disa-
bled until bit C of the DWDR registerhas been set.
ACTIVATION”
(i.e.
When the Watchdog is disabled, low power Stop
mode is available. Once activated, the Watchdog
cannot be disabled, except by resetting the MCU.
In the HARDWARE option, the Watchdog is per-
manently enabled. Sincethe oscillator will run con-
tinuously, low power mode is not available. The
STOP instruction is interpreted as a WAIT instruc-
tion, and the Watchdog continues to countdown.
However, when the EXTERNAL STOP MODE
CONTROL option has been selected low power
consumption may be achieved in Stop Mode.
Execution of the STOP instruction is then gov-
erned by a secondary function associated with the
NMI pin. If a STOP instruction is encountered
when the NMI pin is low, it is interpreted as WAIT,
as described above. If, however, the STOP in-
struction is encountered when the NMI pin is high,
the Watchdog counter is frozen and the CPU en-
ters STOP mode.
When the MCU exits STOP mode(i.e. when anin-
terrupt is generated), the Watchdog resumes its
activity.
Table 6. Recommended Option Choices
Functions Required
Stop Mode & Watchdog
Stop Mode
Watchdog
Recommended Options
“EXTERNAL STOP MODE” & “HARDWARE WATCHDOG”
“SOFTWARE WATCHDOG”
“HARDWARE WATCHDOG”
相關PDF資料
PDF描述
ST63E69 8-Bit EPROM HCMOS MCUs For Digital Controlled Multi Frequency Monitor(應用于數字控制的多頻顯示器的8位EPROM HCMOS微控制器)
ST63T69 8-Bit EPROM HCMOS MCUs For Digital Controlled Multi Frequency Monitor(應用于數字控制的多頻顯示器的8位EPROM HCMOS微控制器)
ST63E85 8-Bit EPROM/OTP MCUs With On-Screen-Display For TV Tuning(應用于電視調諧帶屏幕顯示的8位EPROM/OTP微控制器)
ST63E87 8-Bit EPROM/OTP MCUs With On-Screen-Display For TV Tuning(應用于電視調諧帶屏幕顯示的8位EPROM/OTP微控制器)
ST63T85 8-Bit EPROM/OTP MCUs With On-Screen-Display For TV Tuning(應用于電視調諧帶屏幕顯示的8位EPROM/OTP微控制器)
相關代理商/技術參數
參數描述
ST62T63CB6 功能描述:8位微控制器 -MCU OTP EPROM 2K SPI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST62T63CM6 功能描述:8位微控制器 -MCU OTP EPROM 2K SPI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST62T65CB3 制造商:STMicroelectronics 功能描述:+125C 4K OTP DIP - Rail/Tube
ST62T65CB6 功能描述:8位微控制器 -MCU OTP EPROM 4K SPI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST62T65CB6 制造商:STMicroelectronics 功能描述:8BIT MCU OTP 4K+EEPROM 62T65 DIP