參數資料
| 型號： | ST16C580IQ48-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 15/39頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART FIFO 16B 48TQFP |
| 標準包裝： | 250 |
| 特點： | * |
| 通道數： | 1，UART |
| FIFO's： | 16 字節 |
| 電源電壓： | 2.97 V ~ 5.5 V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-TQFP |
| 供應商設備封裝： | 48-TQFP（7x7） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
ST16C580
22
Rev. 1.22
inputs/outputs. While in this mode, the TX/RX output/
Inputs are routed to the infrared encoder/decoder. The
data input and output levels will conform to the IrDA
infrared interface requirement. As such, while in this
mode the infrared TX output will be a logic 0 during idle
data conditions.
MCR BIT-7:
Logic 0 = Divide by one. The input clock (crystal or
external) is divided by sixteen and then presented to
the Programmable Baud Rate Generator (BGR) with-
out further modification, i.e., divide by one. (normal,
default condition)
Logic 1 = Divide by four. The divide by one clock
described in MCR bit-7 equals a logic 0, is further
divided by four (also see Programmable Baud Rate
Generator section).
Line Status Register (LSR)
This register provides the status of data transfers
between. the 580 and the CPU.
LSR BIT-0:
Logic 0 = No data in receive holding register or FIFO.
(normal default condition)
Logic 1 = Data has been received and is saved in the
receive holding register or FIFO.
LSR BIT-1:
Logic 0 = No overrun error. (normal default condition)
Logic 1 = Overrun error. A data overrun error occurred
in the receive shift register. This happens when addi-
tional data arrives while the FIFO is full. In this case
the previous data in the shift register is overwritten.
Note that under this condition the data byte in the
receive shift register is not transfer into the FIFO,
therefore the data in the FIFO is not corrupted by the
error.
LSR BIT-2:
Logic 0 = No parity error (normal default condition)
Logic 1 = Parity error. The receive character does not
have correct parity information and is suspect. In the
FIFO mode, this error is associated with the character
at the top of the FIFO.
LSR BIT-3:
Logic 0 = No framing error (normal default condition).
Logic 1 = Framing error. The receive character did not
have a valid stop bit(s). In the FIFO mode this error is
associated with the character at the top of the FIFO.
LSR BIT-4:
Logic 0 = No break condition (normal default condi-
tion)
Logic 1 = The receiver received a break signal (RX
was a logic 0 for one character frame time). In the
FIFO mode, only one break character is loaded into
the FIFO.
LSR BIT-5:
This bit is the Transmit Holding Register Empty indi-
cator. This bit indicates that the UART is ready to
accept a new character for transmission. In addition,
this bit causes the UART to issue an interrupt to CPU
when the THR interrupt enable is set. The THR bit is
set to a logic 1 when a character is transferred from the
transmit holding register into the transmitter shift
register. The bit is reset to logic 0 concurrently with the
loading of the transmitter holding register by the CPU.
In the FIFO mode this bit is set when the transmit FIFO
is empty; it is cleared when at least 1 byte is written to
the transmit FIFO.
LSR BIT-6:
This bit is the Transmit Empty indicator. This bit is set
to a logic 1 whenever the transmit holding register and
the transmit shift register are both empty. It is reset to
logic 0 whenever either the THR or TSR contains a
data character. In the FIFO mode this bit is set to one
whenever the transmit FIFO and transmit shift register
are both empty.
LSR BIT-7:
Logic 0 = No Error (normal default condition)
Logic 1 = At least one parity error, framing error or
break indication is in the current FIFO data. This bit is
cleared when LSR register is read.
Modem Status Register (MSR)
This register provides the current state of the control
interface signals from the modem, or other peripheral
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C650AIJ44-F | IC UART FIFO 32B 44PLCC |
| ST16C654DIQ64-F | IC UART FIFO 64B QUAD 64LQFP |
| ST78C34CJ44-F | IC UART FIFO 83B 44PLCC |
| ST78C36ACJ44-F | IC UART FIFO 16B 44PLCC |
| SW06GSZ-REEL | IC SWITCH QUAD SPST 16SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C650 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.90V TO 5.5V UART WITH 32-BYTE FIFO |
| ST16C650A | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.90V TO 5.5V UART WITH 32-BYTE FIFO |
| ST16C650A_0508 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.90V TO 5.5V UART WITH 32-BYTE FIFO |
| ST16C650A_09 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.90V TO 5.5V UART WITH 32-BYTE FIFO |
| ST16C650ACJ44 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。