- 您現在的位置：買賣IC網 > PDF目錄383837 > ST16C452PS (Exar Corporation) Dual UART with Parallel Printer Port(雙通用異步接收器/發送器（帶并行打印機端口）) PDF資料下載
參數資料
| 型號： | ST16C452PS |
| 廠商： | Exar Corporation |
| 英文描述： | Dual UART with Parallel Printer Port(雙通用異步接收器/發送器（帶并行打印機端口）) |
| 中文描述： | 雙UART與并行打印機端口（雙通用異步接收器/發送器（帶并行打印機端口）） |
| 文件頁數： | 5/30頁 |
| 文件大?。?/td> | 389K |
| 代理商： | ST16C452PS |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
5
ST16C452/452PS
Rev. 3.10
SYMBOL DESCRIPTION
Symbol
Pin
Signal Type
Pin Description
port, onto D0-D7 data bus for a read cycle by an external
CPU.
-IOW
36
I
Write strobe.- A logic 0 transition on this pin will transfer the
data on the internal data bus (D0-D7), as defined by either
address bits A0-A2 for UART channels A/B or A0-A1 for the
printer port, into an internal register during a write cycle from
an external CPU.
PD7-PD0
46-53
I/O
Printer Data port (Bi-directional three state) - These pins are
the eight bit, three state data bus for transferring information
to or from an external device (usually a printer). D0 is the
least significant bit. PD7-PD0 are latched during a write
cycle (output mode).
PE
67
I
Paper Empty - General purpose input or line printer paper
empty (Internal pull-up). This pin can be connected to
provide a printer out of paper indication.
RDOUT
44
O
Read Out (active high) - This pin goes to a logic 1 when the
external CPU is reading data from the 452/452PS. This
signal can be used to enable/disable external transceivers
or other logic functions.
-RESET
39
I
Master Reset (active low) - a logic 0 on this pin will reset the
internal registers and all the outputs. The UART transmitter
output and the receiver input will be disabled during reset
time. (See ST16C452/452PS External Reset Conditions for
initialization details.)
N.C.
9,61
Not Used. Should be left open.
SLCT
65
I
Select (with internal pull-up) - General purpose input or line
printer select status. Normally this pin is connected to a
printer output (active low) that indicates the ready status of
a printer, i.e., on-line and/or on-line and ready.
-SLCTIN
58
I/O
Select In (open drain, with internal pull-up) - General
purpose I/O or line printer select. This pin can be read via
Bit-3 in the printer command register, or written via bit-3 in
the printer control register. As this pin is open-drain, it can
be wire-ord with other outputs. Normally this signal is
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C452 | Dual UART with Parallel Printer Port(雙通用異步接收器/發送器（帶并行打印機端口）) |
| ST16C550 | UART with 16-Byte FIFO(通用異步接收器/發送器（帶16字節的先進先出）) |
| ST16C552 | Dual UART with 16-Byte FIFO and Parallel Printer Port(雙通用異步接收器/發送器（帶16字節的先進先出和并行打印機端口）) |
| ST16C552A | Dual UART with 16-Byte FIFO and Parallel Printer Port(雙通用異步接收器/發送器（帶16字節的先進先出和并行打印機端口）) |
| ST16C554DCJ68 | QUAD UART WITH 16-BYTE FIFOS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C454 | 制造商:EXAR 制造商全稱:EXAR 功能描述:QUAD UNIVERSAL ASYNCHRONOUS RECEIVER/TRANSMITTER (UART) |
| ST16C454_05 | 制造商:EXAR 制造商全稱:EXAR 功能描述:QUAD UNIVERSAL ASYNCHRONOUS RECEIVER/TRANSMITTER (UART) |
| ST16C454CJ | 制造商:Exar Corporation 功能描述: |
| ST16C454CJ-0A-EVB | 功能描述:界面開發工具 Supports C454 68 ld PLCC, ISA Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| ST16C454CJ68 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。