- 您現在的位置：買賣IC網 > PDF目錄16492 > SI5013-EVB (Silicon Laboratories Inc)BOARD EVALUATION FOR SI5013 PDF資料下載
參數資料
| 型號： | SI5013-EVB |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 7/26頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION FOR SI5013 |
| 標準包裝： | 1 |
| 主要目的： | 計時，時鐘和數據恢復（CDR） |
| 已用 IC / 零件： | SI5013 |
| 已供物品： | 板 |
| 其它名稱： | 336-1123 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
Si5013
Rev. 1.6
15
4.11.2. Jitter Transfer
The
Si5013
exceeds
all
relevant
Bellcore/ITU
specifications related to SONET/SDH jitter transfer.
Jitter transfer is defined as the ratio of output signal jitter
to input signal jitter as a function of jitter frequency.
These measurements are made with an input test signal
that is degraded with sinusoidal jitter whose magnitude
is defined by the mask in Figure 9.
Figure 9. Jitter Transfer Specification
4.11.3. Jitter Generation
The Si5013 exceeds all relevant specifications for jitter
generation proposed for SONET/SDH equipment. The
jitter generation specification defines the amount of jitter
that may be present on the recovered clock and data
outputs when a jitter free input signal is provided. The
Si5013 typically generates less than 3.0 mUIrms of jitter
when presented with jitter-free input data.
4.12. RESET/DSPLL Calibration
The Si5013 achieves optimal jitter performance by
automatically calibrating the loop gain parameters within
the DSPLL on powerup. Calibration may also be
initiated by a high-to-low transition on the RESET/CAL
pin. The RESET/CAL pin must be held high for at least
1 s. When RESET/CAL is released (set to low) the
digital
logic
resets
to
a
known
initial
condition,
recalibrates the DSPLL, and begins to lock to the
incoming data stream. For a valid reset to occur when
using Reference mode, a proper, external reference
clock frequency must be applied.
4.13. Clock Disable
The Si5013 provides a clock disable pin (CLK_DSBL)
that is used to disable the recovered clock output
(CLKOUT). When the CLK_DSBL pin is asserted, the
positive and negative terminals of CLKOUT are tied to
VDD through 100
Ω on-chip resistors.
4.14. Data Squelch
The Si5013 provides a data squelching pin (DSQLCH)
that is used to set the recovered data output (DOUT) to
binary zero. When the DSQLCH pin is asserted, the
DOUT+ signal is held low and the DOUT– signal is held
high. This pin can be is used to squelch corrupt data
during LOS and LOL situations. Care must be taken
when ac coupling these outputs; a long string of zeros
or ones will not be held through ac coupling capacitors.
4.15. Device Grounding
The Si5013 uses the GND pad on the bottom of the 28-
pin micro leaded package (QFN) for device ground. This
pad should be connected directly to the analog supply
ground. See Figure 15 on page 19 and Figure 16 on
page 23 for the ground (GND) pad location.
4.16. Bias Generation Circuitry
The Si5013 makes use of an external resistor to set
internal bias currents. The external resistor allows
precise generation of bias currents which significantly
reduces
power
consumption
versus
traditional
implementations that use an internal resistor. The bias
generation circuitry requires a 10 k
Ω (1%) resistor
connected between REXT and GND.
4.17. Voltage Regulator
The Si5013 operates from a 3.3 V external supply
voltage. Internally the device operates from a 2.5 V
supply. The Si5013 regulates 2.5 V internally down from
the external 3.3 V supply.
In addition to supporting 3.3 V systems, the on-chip
linear regulator offers better power supply noise
rejection versus a direct 2.5 V supply.
4.18. Differential Input Circuitry
The Si5013 provides differential inputs for both the high-
speed data (DIN) and the reference clock (REFCLK)
inputs. An example termination for these inputs is
shown
in
Figures
and
11,
respectively.
In
applications where direct dc coupling is possible, the
0.1 F capacitors may be omitted. (LOS operation is
only guaranteed when ac coupled.) The data input
limiting amplifier requires an input signal with a
differential peak-to-peak voltage as specified in Table 2
REFCLK
input
differential
peak-to-peak
voltage
requirement is also specified in Table 2.
0.1 dB
Jitter
Transfer
Fc
Frequency
20 dB/Decade
Slope
Fc
(kHz)
SONET
Data Rate
OC-12
OC-3
500
130
Acceptable
Range
相關PDF資料 |
PDF描述 |
|---|---|
| GBC18DRTI-S734 | CONN EDGECARD 36POS DIP .100 SLD |
| ECM25DCTN | CONN EDGECARD 50POS DIP .156 SLD |
| XR16V554IL-0A-EVB | EVAL BOARD FOR XR16V554 48QFN |
| RPP30-2424SW | CONV DC/DC 30W 9-36VIN 24VOUT |
| 1-5492191-7 | CA SM LDS SCAPC-SC/UPC(NG) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI5013-X-GM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:OC-12/3, STM-4/1 SONET/SDH CDR IC WITH LIMITING AMPLIFIER |
| SI-50141-F | 功能描述:CONN MAGJACK 1PT 10/100BTX G/Y RoHS:是 類別:連接器，互連式 >> 模塊 - 帶磁性元件的插座 系列:MagJack® ST SI-50000 標準包裝:63 系列:Mag45 連接器類型:RJ45 端口數:1 行數:1 安裝類型:面板安裝，通孔，直角 速度:10/100 Base-T 板上方高度:0.555"（14.10mm） LED 顏色:綠 - 綠 每一插座芯體的數目:5 屏蔽:屏蔽 翼片方向:上 特點:板鎖 包裝:托盤 |
| SI-50142 | 制造商:BEL 制造商全稱:Bel Fuse Inc. 功能描述:SI-50142 |
| SI-50143 | 制造商:BEL 制造商全稱:Bel Fuse Inc. 功能描述:SI-50143 |
| SI-50144 | 制造商:BEL 制造商全稱:Bel Fuse Inc. 功能描述:SI-50144 |
發布緊急采購，3分鐘左右您將得到回復。