- 您現在的位置：買賣IC網 > PDF目錄385819 > SC16C2552 (NXP Semiconductors N.V.) Dual UART with 16-byte transmit and receive FIFOs PDF資料下載
參數資料
| 型號： | SC16C2552 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Dual UART with 16-byte transmit and receive FIFOs |
| 中文描述： | 雙UART具有16字節的傳輸和接收FIFO |
| 文件頁數： | 16/38頁 |
| 文件大?。?/td> | 579K |
| 代理商： | SC16C2552 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
Philips Semiconductors
SC16C2552
Dual UART with 16-byte transmit and receive FIFOs
Product data
Rev. 03 — 20 June 2003
16 of 38
9397 750 11636
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
3
(continued)
Transmit operation in mode ‘1’:
When the SC16C2552 is in
FIFO mode (FCR[0] = logic 1; FCR[3] = logic 1), the TXRDY pin
will be a logic 1 when the transmit FIFO is completely full. It will be
a logic 0 if one or more FIFO locations are empty.
Receive operation in mode ‘1’:
When the SC16C2552 is in FIFO
mode (FCR[0] = logic 1; FCR[3] = logic 1) and the trigger level has
been reached, or a Receive Time-Out has occurred, the RXRDY
signal at the MF pin will go to a logic 0. Once activated, it will go to
a logic 1 after there are no more characters in the FIFO.
NOTE: The AFR register must be set to the RXRDY mode prior to
any possible reading of the RXRDY signal.
XMIT FIFO reset.
Logic 0 = No FIFO transmit reset (normal default condition).
Logic 1 = Clears the contents of the transmit FIFO and resets
the FIFO counter logic (the transmit shift register is not cleared
or altered). This bit will return to a logic 0 after clearing the FIFO.
RCVR FIFO reset.
Logic 0 = No FIFO receive reset (normal default condition).
Logic 1 = Clears the contents of the receive FIFO and resets the
FIFO counter logic (the receive shift register is not cleared or
altered). This bit will return to a logic 0 after clearing the FIFO.
FIFOs enabled.
Logic 0 = Disable the transmit and receive FIFO (normal default
condition).
Logic 1 = Enable the transmit and receive FIFO.
This bit must
be a ‘1’ when other FCR bits are written to, or they will not
be programmed.
2
FCR[2]
1
FCR[1]
0
FCR[0]
Table 9:
FCR[7]
0
0
1
1
RCVR trigger levels
FCR[6]
0
1
0
1
RX FIFO trigger level
01
04
08
14
Table 8:
Bit
FIFO Control Register bits description
…continued
Symbol
Description
相關PDF資料 |
PDF描述 |
|---|---|
| SC16C2552IA44 | Dual UART with 16-byte transmit and receive FIFOs |
| SC21545 | NKCC1 (N-16) |
| SC26C562 | CMOS dual universal serial communications controller (CDUSCC)(CMOS 雙通用串聯通信控制器(CDUSCC)) |
| SC26C562A8A | CMOS dual universal serial communications controller CDUSCC |
| SC26C562C1A | CMOS dual universal serial communications controller CDUSCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C2552B | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs |
| SC16C2552BIA44 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C2552BIA44,512 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C2552BIA44,518 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C2552BIA44,529 | 功能描述:UART 接口集成電路 2CH. UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。