參數資料
型號： SAL-XC886C-6FFA5V
廠商： INFINEON TECHNOLOGIES AG
元件分類： 微控制器/微處理器
英文描述： 8-BIT, FLASH, 80 MHz, MICROCONTROLLER, PQFP48
封裝： GREEN, PLASTIC, TQFP-48
文件頁數： 129/134頁
文件大?。?/td> 864K
代理商： SAL-XC886C-6FFA5V
SAL-XC886CLM
Functional Description
Data Sheet
87
V1.0, 2010-05
3.15.1
LIN Header Transmission
LIN header transmission is only applicable in master mode. In the LIN communication,
a master task decides when and which frame is to be transferred on the bus. It also
identifies a slave task to provide the data transported by each frame. The information
needed for the handshaking between the master and slave tasks is provided by the
master task through the header portion of the frame.
The header consists of a break and synch pattern followed by an identifier. Among these
three fields, only the break pattern cannot be transmitted as a normal 8-bit UART data.
The break must contain a dominant value of 13 bits or more to ensure proper
synchronization of slave nodes.
In the LIN communication, a slave task is required to be synchronized at the beginning
of the protected identifier field of frame. For this purpose, every frame starts with a
sequence consisting of a break field followed by a synch byte field. This sequence is
unique and provides enough information for any slave task to detect the beginning of a
new frame and be synchronized at the start of the identifier field.
Upon entering LIN communication, a connection is established and the transfer speed
(baud rate) of the serial communication partner (host) is automatically synchronized in
the following steps:
STEP 1: Initialize interface for reception and timer for baud rate measurement
STEP 2: Wait for an incoming LIN frame from host
STEP 3: Synchronize the baud rate to the host
STEP 4: Enter for Master Request Frame or for Slave Response Frame
Note: Re-synchronization and setup of baud rate are always done for every Master
Request Header or Slave Response Header LIN frame.
相關PDF資料
PDF描述
SAL-XC886CLM-8FFA5V 8-BIT, FLASH, 80 MHz, MICROCONTROLLER, PQFP48
SAL-XC886C-8FFA5V 8-BIT, FLASH, 80 MHz, MICROCONTROLLER, PQFP48
SARCC433M92BXP0R12 1-PORT SAW RESONATOR, 433.92 MHz
SARCC315M00BXP0R05 1-PORT SAW RESONATOR, 315 MHz
SARCC423M22BXP0R12 1-PORT SAW RESONATOR, 423.22 MHz
相關代理商/技術參數
參數描述
SAL-XC886CLM 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-Bit Single Chip Microcontroller
SAL-XC886CLM-8FFA 5V AC 功能描述:8位微控制器 -MCU 8-Bit Single Chip Microcontroller RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
SAL-XC886CM-8FFA 5V AC 功能描述:8位微控制器 -MCU 8-Bit Single Chip Microcontroller RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
SAL-XC886LM-8FFA 5V AC 功能描述:8位微控制器 -MCU 8-Bit Single Chip Microcontroller RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
SAM 9 LL-SUB-12-1F 制造商:Timesys Corporation 功能描述:LINUXLINK PRO EDITION FOR ATMEL SAM9 - Virtual or Non-Physical Inventory (Software & Literature)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*