參數資料
型號: SAH-XC2723X-20F66V
廠商: INFINEON TECHNOLOGIES AG
元件分類: 微控制器/微處理器
英文描述: 32-BIT, FLASH, 66 MHz, RISC MICROCONTROLLER, PQCC48
封裝: 0.50 MM PITCH, GREEN, PLASTIC, VQFN-48
文件頁數: 99/112頁
文件大?。?/td> 3116K
代理商: SAH-XC2723X-20F66V
XC2723X
XC2000 Family / Econo Line
Electrical Parameters
PRELIMINARY
Data Sheet
83
V1.0, 2010-12
The timing in the AC Characteristics refers to TCSs. Timing must be calculated using the
minimum TCS possible under the given circumstances.
The actual minimum value for TCS depends on the jitter of the PLL. Because the PLL is
constantly adjusting its output frequency to correspond to the input frequency (from
crystal or oscillator), the accumulated jitter is limited. This means that the relative
deviation for periods of more than one TCS is lower than for a single TCS (see formulas
and Figure 17).
This is especially important for bus cycles using waitstates and for the operation of
timers, serial interfaces, etc. For all slower operations and longer periods (e.g. pulse train
generation or measurement, lower baudrates, etc.) the deviation caused by the PLL jitter
is negligible.
The value of the accumulated PLL jitter depends on the number of consecutive VCO
output cycles within the respective timeframe. The VCO output clock is divided by the
output prescaler K2 to generate the system clock signal
f
SYS. The number of VCO cycles
is K2
× T, where T is the number of consecutive f
SYS cycles (TCS).
The maximum accumulated jitter (long-term jitter) DTmax is defined by:
DTmax [ns] = ±(220 / (K2 × fSYS) + 4.3)
This maximum value is applicable, if either the number of clock cycles T > (
f
SYS / 1.2) or
the prescaler value K2 > 17.
In all other cases for a timeframe of T
× TCS the accumulated jitter D
T is determined by:
DT [ns] = DTmax × [(1 - 0.058 × K2) × (T - 1) / (0.83 × fSYS - 1) + 0.058 × K2]
f
SYS in [MHz] in all formulas.
Example, for a period of 3 TCSs @ 33 MHz and K2 = 4:
Dmax = ±(220 / (4 × 33) + 4.3) = 5.97 ns (Not applicable directly in this case!)
D3 = 5.97 × [(1 - 0.058 × 4) × (3 - 1) / (0.83 × 33 - 1) + 0.058 × 4]
= 5.97
× [0.768 × 2 / 26.39 + 0.232]
= 1.7 ns
Example, for a period of 3 TCSs @ 33 MHz and K2 = 2:
Dmax = ±(220 / (2 × 33) + 4.3) = 7.63 ns (Not applicable directly in this case!)
D3 = 7.63 × [(1 - 0.058 × 2) × (3 - 1) / (0.83 × 33 - 1) + 0.058 × 2]
= 7.63
× [0.884 × 2 / 26.39 + 0.116]
= 1.4 ns
相關PDF資料
PDF描述
SAK-XC2765X-72F80LAA 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP100
SAK-XC2768X-136F128L 32-BIT, FLASH, 128 MHz, RISC MICROCONTROLLER, PQFP100
SAK-XE160FU-4F40R 16-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PDSO38
SAK-XE169FH-136F100L 16-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PQFP176
SAL-TC1766-192F80U 32-BIT, FLASH, 80 MHz, MICROCONTROLLER, UUC231
相關代理商/技術參數
參數描述
SAI Y-4S M8-M8 制造商:Weidmuller 功能描述:SPLITTER PLUG TO 2X RCPT M8 制造商:Weidmuller 功能描述:SPLITTER, PLUG TO 2X RCPT, M8, 4 WAY 制造商:Weidmuller 功能描述:SPLITTER, PLUG TO 2X RCPT, M8, 4 WAY, No. of Ports:2, SVHC:No SVHC (20-Jun-2013)
SAI01 制造商:SANKEN 制造商全稱:Sanken electric 功能描述:Surface-Mount, Separate Excitation Switching Type
SAI01-1 制造商:SANKEN 制造商全稱:Sanken electric 功能描述:Surface-mount and Separate Excitation Type
SAI01V1 制造商:Sanken Electric Co Ltd 功能描述:IC REG BUCK 5V 0.5A PS-4PIN
SAI02 制造商:SANKEN 制造商全稱:Sanken electric 功能描述:Surface-mount and Separate Excitation Type