- 您現在的位置：買賣IC網 > PDF目錄385813 > SAA55XX (NXP Semiconductors N.V.) TV microcontrollers with Closed Captioning (CC) and On-Screen Display (OSD) PDF資料下載
參數資料
| 型號： | SAA55XX |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | TV microcontrollers with Closed Captioning (CC) and On-Screen Display (OSD) |
| 中文描述： | 與隱藏字幕（CC）和屏幕顯示（OSD電視微控制器） |
| 文件頁數： | 31/84頁 |
| 文件大?。?/td> | 352K |
| 代理商： | SAA55XX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
2000 Feb 23
31
Philips Semiconductors
Preliminary specification
TV microcontrollers with Closed Captioning (CC)
and On-Screen Display (OSD)
SAA55xx
9.3
Standby mode
When Standby mode is entered both Acquisition and
Display sections are disabled. The following functions
remain active:
80C51 core
Memory interface
I
2
C-bus interface
Timer/Counters
Watchdog Timer
Software ADC
Pulse Width Modulators
To enter Standby mode, the STANDBY control bit in the
ROMBK SFR (bit 7) must be set. It can be used in
conjunction with either Idle or Power-down modes to
switch between power saving modes. This mode enables
the 80C51 core to decode either IR remote commands or
receive I
2
C-bus commands without the device being fully
powered.
The Standby state is maintained upon exit from either the
Idle mode or Power-down mode. No wake-up from
Standby is necessary as the 80C51 core remains
operational.
Since the output values on RGB and VDS are maintained
the display output must be disabled before entering this
mode.
10 I/O FACILITY
10.1
I/O ports
The SAA55xx devices have 29 I/O lines, each is
individually addressable, or form 3 parallel 8-bit
addressable ports which are Port 0, Port 1 and Port 2.
Port 3 has 5-bit parallel I/Os only.
10.2
Port type
All individual ports can be programmed to function in one
of four I/O configurations: open-drain, quasi-bidirectional,
high-impedance and push-pull. The I/O configuration is
selected using two associated Port Configuration
Registers: PnCFGA and PnCFGB (where n = port number
0, 1, 2 or 3); see Table 3.
10.2.1
O
PEN
-
DRAIN
The open-drain configuration can be used for bidirectional
operation of a port. It requires an external pull-up resistor,
the pull-up voltage has a maximum value of 5.5 V, to allow
connection of the device into a 5 V environment.
Note that the I
2
C-bus ports (P1.4, P1.5, P1.6 and P1.7)
can only be configured as open-drain.
10.2.2
Q
UASI
-
BIDIRECTIONAL
The quasi-bidirectional configuration is a combination of
open-drain and push-pull. It requires an external pull-up
resistor to V
DDP
(nominally 3.3 V). When a signaltransition
from LOW-to-HIGH is output from the device, the pad is
put into push-pull configuration for one clock cycle
(166 ns) after which the pad goes into open-drain
configuration. This configuration is used to speed up the
edges of signal transitions. This is the default state of
operation of the pads after reset.
10.2.3
H
IGH
-
IMPEDANCE
The high-impedance configuration can be used for input
only operation of the port. When using this configuration
the two output transistors are turned off.
10.2.4
P
USH
-
PULL
The push-pull configuration can be used for output only.
In this configuration the signal is driven to either 0 V or
V
DDP
, which is nominally 3.3 V.
10.3
Port alternative functions
Ports 1, 2 and 3 are shared with alternative functions to
enable control of external devices and circuitry.
The alternative functions are enabled by setting the
appropriate SFR and also writing a logic 1 to the port bit
that the function occupies.
10.4
LED support
Port pins P0.5 and P0.6 have a 8 mA current sinking
capability to enable LEDs in series with current limiting
resistors to be driven directly, without the need for
additional buffering circuitry.
相關PDF資料 |
PDF描述 |
|---|---|
| SAA6712E | ECONOLINE: RB & RA - Dual Output from a Single Input Rail- Power Sharing on Output- Industry Standard Pinout- 1kVDC & 2kVDC Isolation- Custom Solutions Available- UL94V-0 Package Material- Efficiency to 85% |
| SAA6713AH | XGA analog input flat panel controller |
| SAA6713H | XGA dual input flat panel controller |
| SAA7110 | Digital Multistandard Colour Decoder(數字多標準彩色譯碼器) |
| SAA7111 | Video Input Processor VIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SAA5603 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| SAA5645 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Enhanced TV microcontrollers with On-Screen Display OSD |
| SAA5645HL | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Enhanced TV microcontrollers with On-Screen Display OSD |
| SAA5647 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Enhanced TV microcontrollers with On-Screen Display OSD |
| SAA5647HL | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Enhanced TV microcontrollers with On-Screen Display OSD |
發布緊急采購，3分鐘左右您將得到回復。