- 您現在的位置：買賣IC網 > PDF目錄374675 > SA25F020LEN (Electronic Theatre Controls, Inc.) RES 82.5 OHM 1/10W .5% 0805 SMD PDF資料下載
參數資料
| 型號： | SA25F020LEN |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | RES 82.5 OHM 1/10W .5% 0805 SMD |
| 中文描述： | 2MB的串行閃存與25MHz的SPI總線接口 |
| 文件頁數： | 33/37頁 |
| 文件大?。?/td> | 560K |
| 代理商： | SA25F020LEN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁
SA25F020 Advanced Information
SAIFUN
33
Powerup and Powerdown
The device must not be selected at
powerup or powerdown (that is, CSb must
follow the voltage applied on V
CC
) until V
CC
reaches the correct value, as follows:
=
V
CC
(min) at powerup, and then for a
further delay of t
PU
(as described in
Table 11)
=
V
SS
at powerdown
A simple pull-up resistor on CSb can
usually be used to insure safe and proper
powerup and powerdown. To avoid data
corruption and inadvertent write operations
during powerup, a Power On Reset (POR)
circuit is included. The logic inside the
device is held at reset while V
CC
is less
than the POR threshold value (V
POR
), all
operations are disabled and the device
does not respond to any instructions.
The device ignores all instructions until a
time delay of t
PU
has elapsed after the
moment that V
CC
rises above the VWI
threshold. However, correct operation of
the device is not guaranteed if by this time
V
CC
is still below V
CC
(min). No Write Status
Register, Program or Erase instructions
should be sent until t
PU
reaches the
minimum V
CC
threshold after V
CC
.
At powerup, the device is in Standby mode
(not SP mode) and the WEN bit is reset.
Normal precautions must be taken for
supply rail decoupling to stabilize the V
CC
feed. Each device in a system should have
the V
CC
rail decoupled by a suitable
capacitor close to the package pins (this
capacitor is generally of the order of
0.1 μF).
All operations are disabled and the device
does not respond to any instructions when
V
CC
drops at powerdown from the
operating voltage to below the V
POR
threshold. (The designer must be aware
that if a powerdown occurs while a Write,
Program or Erase cycle is in progress, data
corruption can result.)
Table 11. Powerup
Symbol
Parameter
Min.
Max
.
Unit
V
POR
POR Threshold
Value
2.2
2.4
V
t
PU
V
CC
(min) to CS
low
2
ms
相關PDF資料 |
PDF描述 |
|---|---|
| SA25F020LEMLFFX | 4 Mbit Uniform Sector, Serial Flash Memory |
| SA25F020LENFX | 4 Mbit Uniform Sector, Serial Flash Memory |
| SA32-11SRWA | 8mm (0.32INCH) SINGLE DIGIT NUMERIC DISPLAY |
| SA36-11YWA | Multiconductor Cable; Number of Conductors:4; Conductor Size AWG:22; No. Strands x Strand Size:Solid; Jacket Material:Polyvinylchloride (PVC); Leaded Process Compatible:Yes; Conductor Material:Copper; Outer Diameter:0.141" RoHS Compliant: Yes |
| SA36-11EWA | 9mm(0.36INCH) SINGLE DIGIT NUMERIC DISPLAYS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SA25F020LENF | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:2Mb Serial Flash with 25MHz SPI Bus Interface |
| SA25F020LENFX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:2Mb Serial Flash with 25MHz SPI Bus Interface |
| SA25TFKHL-C1000-D | 制造商:Delkin Devices 功能描述:256MB SECURE DIGITAL, IND TEMP - Trays |
| SA26 | 功能描述:TVS 二極管 - 瞬態電壓抑制器 SA26 Uni-Directional RoHS:否 制造商:Vishay Semiconductors 極性:Bidirectional 工作電壓: 擊穿電壓:58.9 V 鉗位電壓:77.4 V 峰值浪涌電流:38.8 A 系列: 封裝 / 箱體:DO-214AB 最小工作溫度:- 55 C 最大工作溫度:+ 150 C |
| SA26 _AY _10001 | 制造商:PanJit Touch Screens 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。