- 您現在的位置：買賣IC網 > PDF目錄374675 > SA25F020LEN (Electronic Theatre Controls, Inc.) RES 82.5 OHM 1/10W .5% 0805 SMD PDF資料下載
參數資料
| 型號： | SA25F020LEN |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | RES 82.5 OHM 1/10W .5% 0805 SMD |
| 中文描述： | 2MB的串行閃存與25MHz的SPI總線接口 |
| 文件頁數： | 27/37頁 |
| 文件大?。?/td> | 560K |
| 代理商： | SA25F020LEN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
SA25F020 Advanced Information
SAIFUN
27
Page
Erase
(PE)
The PE instruction sets all 256 bytes in the
selected page to 1. Before it can be
executed, two separate instructions must
be carried out. The device must first be
write enabled via the WREN instruction,
and then a PE sequence, which consists of
one opcode byte and three data bytes may
be executed. The address of the memory
locations to be written must be inside the
page to be erased and outside the
protected address field location selected by
the Block Write Protection level. During an
internal PE cycle, all commands are
ignored except the RDSR instruction.
A PE instruction requires the following
sequence:
1. After the CSb line is pulled low to
select the device, the PE opcode is
transmitted via the SI line, followed
by the 3-byte address.
2. Erasing begins after the CSb pin is
brought
high.
low-to-high transition must occur
during
the
SCK
immediately after the clock in the
last address bit.
The CSb pin's
low
time,
As soon as CSb is driven high, the
self-timed PE cycle (whose duration is
defined as T
PE
) is initiated. While the PE
cycle is in progress, the status register may
be read to check the value of the /RDY bit.
The /RDY bit is 1 during the self-timed PE
cycle, and 0 when it is completed. The
WEN bit is reset at some unspecified time
before the cycle is completed. The
instruction sequence is shown in Figure 17.
The SA25F020 is automatically returned to
the Write Disable state at the completion of
a PE cycle.
NOTES:
1. If the device is not write enabled,
the
device
ignores
instruction and returns to the
standby state when CSb is brought
high. A new CSb falling edge is
required to re-initiate the serial
communication.
2. A PE instruction applied to a page
that is protected by the Block
Protect
(BP1,
described in Table 8, page 18, and
Table 9, page 21) is not executed.
the
PE
BP0)
bits
(as
1
3
2
10
9
8
7
6
5
4
0
31
30
29
28
Instruction
24 Bit Address
1
3
2
0
SCK
SI
MSB
CS
23
21
22
Figure 17. Page Erase (PE) Instruction Sequence
相關PDF資料 |
PDF描述 |
|---|---|
| SA25F020LEMLFFX | 4 Mbit Uniform Sector, Serial Flash Memory |
| SA25F020LENFX | 4 Mbit Uniform Sector, Serial Flash Memory |
| SA32-11SRWA | 8mm (0.32INCH) SINGLE DIGIT NUMERIC DISPLAY |
| SA36-11YWA | Multiconductor Cable; Number of Conductors:4; Conductor Size AWG:22; No. Strands x Strand Size:Solid; Jacket Material:Polyvinylchloride (PVC); Leaded Process Compatible:Yes; Conductor Material:Copper; Outer Diameter:0.141" RoHS Compliant: Yes |
| SA36-11EWA | 9mm(0.36INCH) SINGLE DIGIT NUMERIC DISPLAYS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SA25F020LENF | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:2Mb Serial Flash with 25MHz SPI Bus Interface |
| SA25F020LENFX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:2Mb Serial Flash with 25MHz SPI Bus Interface |
| SA25TFKHL-C1000-D | 制造商:Delkin Devices 功能描述:256MB SECURE DIGITAL, IND TEMP - Trays |
| SA26 | 功能描述:TVS 二極管 - 瞬態電壓抑制器 SA26 Uni-Directional RoHS:否 制造商:Vishay Semiconductors 極性:Bidirectional 工作電壓: 擊穿電壓:58.9 V 鉗位電壓:77.4 V 峰值浪涌電流:38.8 A 系列: 封裝 / 箱體:DO-214AB 最小工作溫度:- 55 C 最大工作溫度:+ 150 C |
| SA26 _AY _10001 | 制造商:PanJit Touch Screens 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。