- 您現在的位置：買賣IC網 > PDF目錄374648 > S2204 (Applied Micro Circuits Corp.) Quad GigaBit Ethernet Transceiver(帶鎖相環時鐘合成器的四千兆位以太網收發器) PDF資料下載
參數資料
| 型號： | S2204 |
| 廠商： | Applied Micro Circuits Corp. |
| 英文描述： | Quad GigaBit Ethernet Transceiver(帶鎖相環時鐘合成器的四千兆位以太網收發器) |
| 中文描述： | 四個千兆以太網收發器（帶鎖相環時鐘合成器的四千兆位以太網收發器） |
| 文件頁數： | 11/33頁 |
| 文件大小： | 339K |
| 代理商： | S2204 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
11
S2204
QUAD GIGABIT ETHERNET DEVICE
October 9, 2000 / Revision E
Figure 9. S2204 Diagnostic Loopback Operation
CRU
CSU
OTHER OPERATING MODES
Operating Frequency Rate
The S2204 is designed to operate at the Gigabit
Ethernet rate of 1.250 GHz.
Loopback Mode
When loopback mode is enabled, the serial data
from the transmitter is provided to the serial input of
the receiver, as shown in Figure 9. This provides the
ability to perform system diagnostics and off-line
testing of the interface to verify the integrity of the
serial channel. Loopback mode is enabled indepen-
dently for each channel using its respective
loopback-enable input, LPEN.
TEST MODES
The RESET pin is used to initialize the Transmit
FIFOs and must be asserted (LOW) prior to entering
the normal operational state (see section Transmit
FIFO Initialization).
Note: Serial output data remains active during loopback opera-
tion to enable other system tests to be performed.
JTAG TESTING
The JTAG implementation for the S2204 is compli-
ant with the IEEE1149.1 requirements. JTAG is used
to test the connectivity of the pins on the chip. The
TAP, (Test Access Port), provides access to the test
logic of the chip. When TRST is asserted the TAP is
initialized. TAP is a state machine that is controlled
by TMS. The test instruction and data are loaded
through TDI on the rising edge of TCK. When TMS is
high the test instruction is loaded into the instruction
register. When TMS is low the test data is loaded
into the data register. TDO changes on the falling
edge of TCK. All input pins, including clocks, that
have boundary scan are observe only. They can be
sampled in either normal operational or test mode.
All output pins that have boundary scan, are observe
and control. They can be sampled as they are driven
out of the chip in normal operational mode, and they
can be driven out of the chip in test mode using the
Extest instruction. Since JTAG testing operates only
on digital signals there are some pins with analog
signals that JTAG does not cover. The JTAG imple-
mentation has the three required instruction, Bypass,
Extest, and Sample/Preload.
Instruction
BYPASS
EXTEST
SAMPLE/PRELOAD
ID CODE
Code
11
00
01
10
JTAG Instruction Description:
The BYPASS register contains a single shift-register
stage and is used to provide a minimum-length serial
path between the TDI and TDO pins of a component
when no test operation of that component is re-
quired. This allows more rapid movement of test
data to and from other components on a board that
are required to perform test operations.
The EXTEST instruction allows testing of off-chip cir-
cuitry and board level interconnections. Data would
typically be loaded onto the latched parallel outputs
of boundary-scan shift-register stages using the
SAMPLE/PRELOAD instruction prior to selection of
the EXTEST instruction.
The SAMPLE/PRELOAD instruction allows a snap-
shot of the normal operation of the component to be
taken and examined. It also allows data values to be
loaded onto the latched parallel outputs of the
boundary-scan shift register prior to selection of the
other boundary-scan test instructions.
The following table provides a list of the pins that are
JTAG tested. Each port has a boundary scan regis-
ter (BSR), unless otherwise noted. The following fea-
tures are described: the JTAG mode of each
register (input, output2, or internal (refers to an inter-
nal package pin)), the direction of the port if it has a
boundary scan register (in or out), and the position
of this register on the scan chain.
相關PDF資料 |
PDF描述 |
|---|---|
| S22MD2 | Photothyristor Coupler |
| S22MD3 | MICA RoHS Compliant: No |
| S22MD1V | Silver Mica Capacitor; Capacitance:2400pF; Capacitance Tolerance:+/- 5%; Series:CM06; Voltage Rating:500VDC; Capacitor Dielectric Material:Mica; Termination:Radial Leaded; Lead Pitch:8.7mm; Leaded Process Compatible:No RoHS Compliant: No |
| S2370 | HIGH SPEED, HIGH CURRENT SWITCHING APPLICATIONS. |
| S24A | 500 Watt Peak Power MiniMOSORB Zener Transient Voltage Suppressor(24V峰值反向電壓，500W峰值功率，MiniMOSORB齊納瞬變電壓抑制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S2204TB | 制造商:AppliedMicro 功能描述:QUAD GIGABIT ETHERNET DEVICE |
| S2204TRC | 制造商:AppliedMicro 功能描述: 制造商:AMC 功能描述: |
| S-220-611 | 制造商:Schroff/Pentair Electronic Packaging 功能描述: 制造商:Pentair Technical Products / Hoffman 功能描述:EMC KIT 6U INJECTOR/EJECTOR 制造商:PENTAIR TECNICAL PRODCUTS 功能描述:EMC KIT 6U INJECTOR/EJECTOR |
| S2207 | 功能描述:塑料硬件 WASHER FOR 3501FP RoHS:否 制造商:3M Electronic Specialty 類型:Cylindrical Bumpers |
| S-2207 | 功能描述:WASHER FLAT INSUL FOR SC1133-ND RoHS:否 類別:硬件，緊固件，配件 >> 墊圈 系列:- 標準包裝:100 系列:- 類型:扁平 螺紋/螺釘/孔尺寸:#10 螺釘尺寸 直徑 - 內部:0.196"（4.98mm） 直徑 - 外部:0.500"（12.70mm）1/2" 厚度:0.047"（1.19mm） 鍍層:- 材質:尼龍 其它名稱:3177K |
發布緊急采購，3分鐘左右您將得到回復。