- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C63567F0A0100 MICROCONTROLLER, PQFP144 PDF資料下載
參數資料
| 型號： | S1C63567F0A0100 |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | MICROCONTROLLER, PQFP144 |
| 封裝： | PLASTIC, QFP-144 |
| 文件頁數： | 61/172頁 |
| 文件大?。?/td> | 1349K |
| 代理商： | S1C63567F0A0100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁當前第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁
S1C63567 TECHNICAL MANUAL
EPSON
143
CHAPTER 5: SUMMARY OF NOTES
Sound generator
(1) Since the BZ and XBZ signals are generated asynchronous to the BZE register, hazards may be pro-
duced when the signal goes ON/OFF due to the setting of the BZE register.
(2) The one-shot output is only valid when the normal buzzer output is OFF (BZE = "0") and will be
invalid when the normal buzzer output is ON (BZE = "1").
(3) Since the BZ and XBZ signals are the special outputs of the R01 and R00 ports, it is necessary to set the
high impedance control registers (R01HIZ, R00HIZ) to "0", the data registers (R01, R00) to "1" and the
output selection registers (BZOUT, XBZOUT) to "1" before setting the BZE register to "1".
(4) The buzzer signal is generated by dividing the OSC1 oscillation clock. Since the frequencies and times
that are described in this manual are the values in the case of crystal oscillation (32.768 kHz, Typ.),
they differ when CR oscillation (60 kHz, Typ.) is selected.
SVD circuit
(1) To obtain a stable detection result, the SVD circuit must be ON for at least l00 sec. So, to obtain the
SVD detection result, follow the programming sequence below.
1. Set SVDON to "1"
2. Maintain for 100 sec minimum
3. Set SVDON to "0"
4. Read SVDDT
(2) The SVD circuit should normally be turned OFF because SVD operation increase current consump-
tion.
Telephone function
(1) It is necessary to turn the OSC3 oscillation on prior to a dialing operation in tone mode because the
tone mode uses the OSC3 (3.58 MHz) clock. However it increases current consumption. Therefore,
turn the OSC3 oscillation off after finishing the dialling operation in tone mode.
(2) Do not write "0" (0000B) to the IDP, FTS, PTS or TCD (in pulse mode) registers because it may cause a
malfunction.
(3) The pause function control bit PAUSE (FF14HD1) and the flash function control bit FLASH
(FF14HD0) are write-only, so software cannot control these functions (on address FF14H) using an
ALU instruction (AND, OR ...). Furthermore, be aware that the pause function or the flash function is
canceled when "0" is written to the PAUSE bit (FF14HD1) or the FLASH bit (FF14HD0).
Interrupt
(1) The interrupt factor flags are set when the interrupt condition is established, even if the interrupt
mask registers are set to "0".
(2) After an interrupt occurs, the same interrupt will occur again if the interrupt enabled state (I flag =
"1") is set or the RETI instruction is executed unless the interrupt factor flag is reset. Therefore, be sure
to reset (write "1" to) the interrupt factor flag in the interrupt service routine before shifting to the
interrupt enabled state.
(3) After an initial reset, all the interrupts including NMI are masked until both the stack pointers SP1
and SP2 are set with the software. Be sure to set the SP1 and SP2 in the initialize routine.
Further, when re-setting the stack pointer, the SP1 and SP2 must be set as a pair. When one of them is
set, all the interrupts including NMI are masked and interrupts cannot be accepted until the other one
is set.
相關PDF資料 |
PDF描述 |
|---|---|
| S1C63653F | 4-BIT, FLASH, 4 MHz, MICROCONTROLLER, CQFP100 |
| S1C6F567D0A0100 | MICROCONTROLLER, UUC141 |
| S1C6N3B0D0A0100 | MICROCONTROLLER, UUC54 |
| S1C6P366D0A0100 | 4-BIT, FLASH, 4.1 MHz, MICROCONTROLLER, UUC102 |
| S1C6P466D0A0A00 | MICROCONTROLLER, UUC140 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C63616 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63632 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63653 | 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller |
| S1C63656 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63657 | 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。