- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C63567F0A0100 MICROCONTROLLER, PQFP144 PDF資料下載
參數資料
| 型號： | S1C63567F0A0100 |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | MICROCONTROLLER, PQFP144 |
| 封裝： | PLASTIC, QFP-144 |
| 文件頁數： | 25/172頁 |
| 文件大小： | 1349K |
| 代理商： | S1C63567F0A0100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁
110
EPSON
S1C63567 TECHNICAL MANUAL
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Telephone Function)
4.14.2 Mask option
Output specifications for the DP terminal is selected from between complementary output and Nch open
drain output by mask option.
Since the R10 to R13 terminals are used for XTMUTE, XRMUTE, HDO and HFO outputs, the output
specifications of the output ports R10–R13 apply to their output specifications. Either complementary
output or Nch open drain output can be selected for each terminal by the output port mask option.
However, even when Nch open drain output is selected, voltage exceeding source voltage must not be
applied to the output terminals.
Mask option allows use of the DTS (tone duration time selection) function. If DTS is used, the tone
duration time can be set to 47 msec or 94 msec using the DTS (FF16HD2) register. If not, the register is
always set to "0". So the tone duration time is fixed at 94 msec.
4.14.3 Operation of telephone function
To realize the operation of the telephone function, dialing procedure is the most important concept. This
procedure contains three steps: (1) setting, (2) executing and (3) interrupt.
(1) Setting
Every function has its control registers. It is necessary to set the appropriate control registers before
execution. Table 4.14.3.1 lists the relations of functions and control registers.
Table 4.14.3.1 Control registers and default setting
Functions
DTMF
DP
PAUSE
FLASH
Control registers
TPS
(FF10HD3)
SINC, SINR (FF16H)
DTS
(FF16HD2)
TPS
(FF10HD3)
MB
(FF10HD1)
DRS
(FF10HD0)
IDP3–IDP0 (FF15H)
PTS3–PTS0 (FF11H)
FTS3–FTS0 (FF12H)
Initial setting
Tone mode
Dual tone
Tone duration selection
Tone mode
40 : 60
10 pps
750 ms
4 sec
563 ms
See Section 4.14.10, "I/O memory of telephone function", for details of each control register.
Operating mode
This dialer has built-in a DTMF generator for generating tones and a DP generator for generating dial
pulses. Two basic operating modes are provided: tone mode and pulse mode. The mode can be
switched by software (TPS register). This setting must be performed prior to the dial processing. At
initial reset, tone mode is set.
The following operating condition should be set according to the operating mode:
Tone mode:
Selecting single tone or dual tone output
Selecting minimum tone duration time (depending on mask option selection)
Pulse mode:
Setting a make ratio (40:60 or 33.3:66.6)
Setting a pulse rate (10 pps or 20 pps)
Setting an inter digit pause time (94 msec to 1,406 msec; selected from among 15 types)
Details will be discussed later.
The tone mode uses the OSC3 (3.58 MHz) clock, so the OSC3 oscillation must be turned ON (OSCC =
"1") prior to dialing. However, it is not necessary to switch the CPU system clock to OSC3.
When executing the pause or flash function, the period of time should be set.
Pause time:
1 to 15 sec (1-sec units; selected from among 15 types)
Flash time:
94 msec to 1,406 msec (selected from among 15 types)
相關PDF資料 |
PDF描述 |
|---|---|
| S1C63653F | 4-BIT, FLASH, 4 MHz, MICROCONTROLLER, CQFP100 |
| S1C6F567D0A0100 | MICROCONTROLLER, UUC141 |
| S1C6N3B0D0A0100 | MICROCONTROLLER, UUC54 |
| S1C6P366D0A0100 | 4-BIT, FLASH, 4.1 MHz, MICROCONTROLLER, UUC102 |
| S1C6P466D0A0A00 | MICROCONTROLLER, UUC140 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C63616 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63632 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63653 | 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller |
| S1C63656 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63657 | 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。