參數資料
型號： R2043T
廠商： Ricoh Co., Ltd.
英文描述： 4-wire Serial Interface
中文描述： 4線串行接口
文件頁數： 37/48頁
文件大?。?/td> 458K
代理商： R2043T
R2043K/T
12345
Rev.2.05 - 37 -
Q
Alarm and Periodic Interrupt
The R2043K/T incorporates the alarm interrupt circuit and the periodic interrupt circuit that are configured to
generate alarm signals and periodic interrupt signals for output from the /INTR pin as described below.
(1) Alarm Interrupt Circuit
The alarm interrupt circuit is configured to generate alarm signals for output from the /INTR, which is driven low
(enabled) upon the occurrence of a match between current time read by the time counters (the day-of-week,
hour, and minute counters) and alarm time preset by the alarm registers (the Alarm_W registers intended for the
day-of-week, hour, and minute digit settings and the Alarm_D registers intended for the hour and minute digit
settings).
(2) Periodic Interrupt Circuit
The periodic interrupt circuit is configured to generate either clock pulses in the pulse mode or interrupt signals in
the level mode for output from the /INTR pin depending on the CT2, CT1, and CT0 bit settings in the control
register 1.
The above two types of interrupt signals are monitored by the flag bits (i.e. the WAFG, DAFG, and CTFG bits in
the Control Register 2) and enabled or disabled by the enable bits (i.e. the WALE, DALE, CT2, CT1, and CT0
bits in the Control Register 1) as listed in the table below.
Flag bits
Enable bits
Alarm_W
WAFG
(D1 at Address Fh)
(D7 at Address Eh)
Alarm_D
DAFG
(D0 at Address Fh)
(D6 at Address Eh)
Peridic interrupt
CTFG
(D2 at Address Fh)
(These bit setting of “0” disable the Periodic Interrupt)
(D2 to D0 at Address Eh)
* At power-on, when the WALE, DALE, CT2, CT1, and CT0 bits are set to 0 in the Control Register 1,
the /INTR pin is driven high (disabled).
* When two types of interrupt signals are output simultaneously from the /INTR pin, the output from the
/INTR pin becomes an OR waveform of their negative logic.
Example: Combined Output to /INTR Pin Under Control of
/ALARM_D and Periodic Interrupt
WALE
DALE
CT2=CT1=CT0=0
In this event, which type of interrupt signal is output from the /INTR pin can be confirmed by reading the
DAFG, and CTFG bit settings in the Control Register 2.
Alarm Interrupt
The alarm interrupt circuit is controlled by the enable bits (i.e. the WALE and DALE bits in the Control Register 1)
and the flag bits (i.e. the WAFG and DAFG bits in the Control Register 2). The enable bits can be used to
enable this circuit when set to 1 and to disable it when set to 0. When intended for reading, the flag bits can be
used to monitor alarm interrupt signals. When intended for writing, the flag bits will cause no event when set to
1 and will drive high (disable) the alarm interrupt circuit when set to 0.
The enable bits will not be affected even when the flag bits are set to 0. In this event, therefore, the alarm
interrupt circuit will continue to function until it is driven low (enabled) upon the next occurrence of a match
between current time and preset alarm time.
Periodic Interrupt
/INTR
/Alarm_D
O
相關PDF資料
PDF描述
R2043T-E2 4-wire Serial Interface
R2043K 4-wire Serial Interface
R2043K-E2 4-wire Serial Interface
R3111Q181B LOW VOLTAGE DETECTOR
R3111Q191A LOW VOLTAGE DETECTOR
相關代理商/技術參數
參數描述
R2043T-E2 制造商:RICOH 制造商全稱:RICOH electronics devices division 功能描述:4-wire Serial Interface
R20440 制造商:Microsemi Corporation 功能描述:STD RECOVERY RECTFR 400V 12A 2PIN DO-4 - Bulk
R2045D 制造商:RICOH 制造商全稱:RICOH electronics devices division 功能描述:4-wire Serial Interface Real Time Clock Module
R2045S 制造商:RICOH 制造商全稱:RICOH electronics devices division 功能描述:4-wire Serial Interface Real Time Clock Module
R20460 制造商:Microsemi Corporation 功能描述:STD RECOVERY RECTFR 600V 12A 2PIN DO-4 - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*