參數資料
型號: PSD954F2
英文描述: Configurable Memory System on a Chip for 8-Bit Microcontrollers(用于8位MCU的可配置存儲器系統)
中文描述: 在8片位微控制器可配置存儲系統(用于8位微控制器的可配置存儲器系統)
文件頁數: 59/90頁
文件大?。?/td> 543K
代理商: PSD954F2
Preliminary Information
PSD9XX Family
55
The
PSD9XX
Functional
Blocks
(cont.)
Access
Recovery Time
to Normal
Access
5V V
CC
,
Typical
Standby
Current
50 μA
(Note 2)
PLD
Memory
Access
Time
Propagation
Delay
Normal tpd
(Note 1)
Mode
Power Down
No Access
tLVDV
Table 30. PSD9XX Timing and Standby Current During Power
Down Mode
NOTES:
1. Power Down does not affect the operation of the PLD. The PLD operation in this
mode is based only on the Turbo Bit.
2. Typical current consumption assuming no PLD inputs are changing state and
the PLD Turbo bit is off.
Port Function
MCU I/O
PLD Out
Address Out
Data Port
Pin Level
No Change
No Change
Undefined
Three-State
Table 29. Power Down Mode’s Effect on
Ports
9.5.1 Automatic Power Down (APD) Unit and Power Down Mode (cont.)
Power Down Mode
By default, if you enable the PSD APD unit, Power Down Mode is automatically enabled.
The device will enter Power Down Mode if the address strobe (ALE/AS) remains inactive
for fifteen CLKIN (pin PD1) clock periods.
The following should be kept in mind when the PSD is in Power Down Mode:
If the address strobe starts pulsing again, the PSD will return to normal operation.
The PSD will also return to normal operation if either the CSI input returns low or the
Reset input returns high.
The MCU address/data bus is blocked from all memories and PLDs.
Various signals can be blocked (prior to Power Down Mode) from entering the PLDs
by setting the appropriate bits in the PMMR registers. The blocked signals include
MCU control signals and the common clock (CLKIN). Note that blocking CLKIN from
the PLDs will not block CLKIN from the APD unit.
All PSD memories enter Standby Mode and are drawing standby current. However,
the PLDs and I/O ports do
not
go into Standby Mode because you don’t want to
have to wait for the logic and I/O to “wake-up” before their outputs can change. See
table 29 for Power Down Mode effects on PSD ports.
Typical standby current is 50 μA for 5 V parts. This standby current value assumes
that there are no transitions on any PLD input.
HC11 (or compatible) Users Note
The HC11 turns off its E clock when it sleeps. Therefore, if you are using an HC11
(or compatible) in your design, and you wish to use the Power Down, you must not
connect the E clock to the CLKIN input (PD1). You should instead connect an
independent clock signal to the CLKIN input. The clock frequency must be
less than
15 times the frequency of AS. The reason for this is that if the frequency is greater than
15 times the frequency of AS, the PSD9XX will keep going into Power Down Mode.
相關PDF資料
PDF描述
PSDS0804T-150M(中文) PSDS SERIES SHIELDING SURFACE MOUNTABLE INDUCTOR(PSDS系列屏蔽貼片電感(與Coil-Craft DS系列,Vishay-Dale IDSC系列產品兼容))
PSDS0804T-100M(中文) PSDS SERIES SHIELDING SURFACE MOUNTABLE INDUCTOR(PSDS系列屏蔽貼片電感(與Coil-Craft DS系列,Vishay-Dale IDSC系列產品兼容))
PSDS1306T-100M(中文) PSDS SERIES SHIELDING SURFACE MOUNTABLE INDUCTOR(PSDS系列屏蔽貼片電感(與Coil-Craft DS系列,Vishay-Dale IDSC系列產品兼容))
PSDS1306T-101M(中文) PSDS SERIES SHIELDING SURFACE MOUNTABLE INDUCTOR(PSDS系列屏蔽貼片電感(與Coil-Craft DS系列,Vishay-Dale IDSC系列產品兼容))
PSDS0804T-1R0M(中文) PSDS SERIES SHIELDING SURFACE MOUNTABLE INDUCTOR(PSDS系列屏蔽貼片電感(與Coil-Craft DS系列,Vishay-Dale IDSC系列產品兼容))
相關代理商/技術參數
參數描述
PSD954F2-90J 功能描述:SPLD - 簡單可編程邏輯器件 U 511-PSD854F2-90J RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD954F2-90M 功能描述:SPLD - 簡單可編程邏輯器件 U 511-PSD854F2-90M RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD954F2V-90J 功能描述:SPLD - 簡單可編程邏輯器件 5.0V 2M 90ns RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD954F2V-90M 功能描述:SPLD - 簡單可編程邏輯器件 PQFP-52 3V 2M 90NS RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PS-DA0104-01 制造商:POWER-SYSTEMS 制造商全稱:Power Systems GmbH+Co.KG 功能描述:DC-AC INVERTER UNIT 4 W SINGLE OUTPUTS