參數資料
型號： PSD813F4
英文描述： Flash In System Programmable Mirocomputer Peripherals(閃速，在系統可編程微控制器外圍器件，1M位閃速存儲器，256K位EEPROM，16K位SRAM)
中文描述： Flash在系統可編程Mirocomputer外設（閃速，在系統可編程微控制器外圍器件，100萬位閃速存儲器，256K位的EEPROM，16K的位的SRAM）
文件頁數： 24/130頁
文件大?。?/td> 650K
代理商： PSD813F4
PSD813F Famly
Prelimnary
20
9.1.1.5.4 Read the OTP Row (PSD813F1 only)
There are 64 bytes of One-Time-Programmable (OTP) memory that reside in EEPROM.
These 64 bytes are in addition to the 32 Kbytes of EEPROM memory. A read of the
OTP row is done with an instruction composed of at least 4 operations: 3 specific write
operations and one to 64 read operations (see Table 9). During the read operation(s),
address bit A6 must be zero, while address bits A5-A0 define the OTP Row byte to be read
while any EEPROM sector select signal (EESi) is active. After reading the last byte, an
EEPROM Return instruction must be executed (see Table 9).
9.1.1.5.5 Read the Erase/ProgramStatus Bits
The PSD813F provides several status bits to be used by the microcontroller to confirm
the completion of an erase or programming instruction of Flash memory. Bits are also
available to show the status of writes to EEPROM. These status bits minimize the time that
the microcontroller spends performing these tasks and are defined in Table 10. The status
bits can be read as many times as needed.
FSi/
CSBOOTi
EESi
DQ7
DQ6
DQ5
DQ4
DQ3
DQ2
DQ1
DQ0
Data
Polling
Toggle
Flag
Error
Flag
Erase
Time-
out
Flash
V
IH
V
IL
X
X
X
X
EEPROM
V
IL
V
IH
Data
Polling
Toggle
Flag
X
X
X
X
X
X
Table 10. Status Bit
NOTES:
1. X = Not guaranteed value, can be read either 1 or 0.
2. DQ7-DQ0 represent the Data Bus bits, D7-D0.
3. FSi/CSBOOTi and EESi are active high.
The
PSD813F
Functional
Blocks
(cont.)
For Flash memory, the microcontroller can perform a read operation to obtain these status
bits while an erase or program instruction is being executed by the embedded algorithm.
See section 9.1.1.7 for details.
For EEPROM not in SDP mode, the microcontroller can perform a read operation to obtain
these status bits just after a data write operation. The microcontroller may write one to 64
bytes before reading the status bits. See section 9.1.1.6 for details.
For EEPROM in SDP mode, the microcontroller will perform a read operation to obtain
these status bits while an SDP write instruction is being executed by the embedded
algorithm. See section 9.1.1.1.3 for details.
相關PDF資料
PDF描述
PSD813F Flash In-System-Programmable Microcontroller Peripherals(閃速，在系統可編程微控制器外圍器件，1M位閃速存儲器，256K位EEPROM，16K位SRAM)
PSD813FH(中文) Field Programmble Microcontroller Peripherals With Flash Memory(帶閃存的現場可編程微控制器)
PSD813FN(中文) Field Programmble Microcontroller Peripherals(帶閃存的現場可編程微控制器)
PSD813FN Field Programmble Microcontroller Peripherals(帶閃存的現場可編程微控制器)
PSD813FH Field Programmble Microcontroller Peripherals With Flash Memory(帶閃存的現場可編程微控制器)
相關代理商/技術參數
參數描述
PSD813F4-15J 制造商:WSI 功能描述:
PSD813F4-15JI 制造商:WSI 功能描述:
PSD813F4A-90J 功能描述:SPLD - 簡單可編程邏輯器件 U 511-PSD813F2A-90J RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD813F4A-90M 功能描述:SPLD - 簡單可編程邏輯器件 U 511-PSD813F2A-90M RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD813F4VA-15J 功能描述:SPLD - 簡單可編程邏輯器件 U 511-PSD813F2VA-15J RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*