參數資料
型號： POE-VOICE-RD
廠商： Silicon Laboratories Inc
文件頁數： 96/108頁
文件大?。?/td> 0K
描述： KIT REF DESIGN PWR OVER ETHERNET
標準包裝： 1
主要目的： 參考設計，以太網供電（POE），語音傳輸
嵌入式： 是，MCU，8 位
已用 IC / 零件： C8051F340，CP2201，Si3400
主要屬性： 嵌入式以太網，以太網供電，8 kHz 語音采樣系統
次要屬性： 圖形用戶界面
已供物品： 板，線纜，電源，軟件
產品目錄頁面： 626 (CN2011-ZH PDF)
相關產品： 336-1385-ND - IC POWER OVER ETHERNET 20QFN
336-1322-ND - IC POWER OVER ETHERNET 20QFN
336-1313-ND - IC ETH CTRLR SNGL-CHIP 28QFN
336-1298-ND - IC 8051 MCU FLASH 64K 48TQFP
其它名稱： 336-1326
CP2200/1
88
Rev. 1.0
15. Physical Layer (PHY)
The CP2200/1 has an IEEE 802.3 compliant 10 BASE-T Ethernet physical layer transceiver that includes a
receiver, transmitter, auto-negotiation, loopback, jabber, smart squelch, polarity correction, and link integrity
functions. If enabled, the auto-negotiation function automatically negotiates the speed of the data link and the
duplex mode. Both half-duplex and full-duplex modes are supported.
The physical layer is controlled and monitored through three registers: PHYCN, PHYCF, and PHYSTA. The various
functions and test modes that can be enabled and monitored through these registers are explained in the following
sections.
15.1. Auto-Negotiation and Duplex Mode
Auto-negotiation allows the CP2200/1 to be connected to any 10/100/1000 BASE-T Ethernet network and
advertise its capabilities. Auto-negotiation uses a series of fast link pulses to send 16-bit link code words. Many
conditions (e.g., failure to detect fast link pulses) can cause auto-negotiation to fail. On failure, the Auto-Negotiation
Failed interrupt will be generated, and/or the Auto-Negotiation Complete Interrupt will not be generated. The
PHYSTA status register will indicate the cause of failure, and the physical layer will default to half-duplex mode. On
success, the Auto-Negotiation Complete interrupt will be generated, and the Auto-Negotiation Failed interrupt will
not be generated. Both interrupts must be checked to ensure that Auto-Negotiation has succeeded.
The advertised link speed will always be 10BASE-T. The duplex mode (half or full) will be negotiated, and full
duplex will be selected if supported by the network. Full duplex mode allows the physical layer to send and receive
data at the same time. In half duplex mode, data can only be transmitted or received at any given time. Full duplex
mode provides overall higher performance and reduces collisions. Software may also choose to advertise its ability
to send and receive PAUSE control packets by setting ADPAUSE (PHYCF.2) to ‘1’.
Important Note: When using auto-negotiation, the auto-negotiation enable bit AUTONEG (PHYCF.4) must
be set to ‘1’ prior to enabling the physical layer. To restart auto-negotiation, the physical layer (transmitter,
receiver, or both) must be disabled and reenabled.
Important Note: The CP220x supports legacy link partners that cannot auto-negotiate. If the link partner cannot
autonegotiate, then the physical layer will default to half-duplex mode.
15.2. Auto-Negotiation Synchronization
The CP220x implements an autonegotiation scheme where autonegotiation is attempted for 250 ms, then a break-
link delay of 1.5 seconds is inserted between auto-negotiation attempts. When the break-link delay is active, the
CP220x does not listen for incoming auto-negotiation requests and does not attempt to auto-negotiate. If one
device starts autonegotiation while the other device is in its “break-link period”, the autonegotiation attempt will fail.
If the devices are unsyncronized, this can lead to a situation where each device attempts to autonegotiate in the
other device’s “break-link period”. This can be solved by synchronizing one or both devices using the following
procedure:
Step 1: Disable the physical layer by writing 0x00 to the PHYCN register.
Step 2: Enable the physical layer with link integrity test and auto-negotiation turned off.
1.Disable the transmitter power save mode (TXPWR = 0x80) and set physical layer options
(PHYCF = SMSQ | JABBER | ADPAUSE | AUTOPOL).
2.Enable the physical layer (PHYEN = 1).
3.Wait for the physical layer to power up. See Physical Layer Startup Time in Table 22 on page 93.
4.Enable the transmitter and receiver (TXEN = 1 and RXEN = 1).
Step 3: Poll the Wake-on-LAN interrupt flag (WAKEINT) to detect if a link partner is present.
1.If there is a signal, wait 250 ms then begin autonegotiation.
2.If there is no signal, wait 1.5 seconds then begin autonegotiation.
相關PDF資料
PDF描述
CW252016-R10G INDUCTOR 100NH 1008 SMD
GBA31DCBI CONN EDGECARD 62POS R/A .125 SLD
EBC18DRTH-S93 CONN EDGECARD 36POS DIP .100 SLD
ABM10DSUH CONN EDGECARD 20POS .156 DIP SLD
UPZ2D331MHD6 CAP ALUM 330UF 200V 20% RADIAL
相關代理商/技術參數
參數描述
POF 1200AE 制造商:Bosch Sensortec 功能描述:ROUTER 1200W
POF 1400ACE 制造商:Bosch Sensortec 功能描述:ROUTER, 1400W
POF-12664 功能描述:PUSH-ON FEET BLK .62 X .20" RoHS:是 類別:硬件，緊固件，配件 >> 緩沖器，支腳，焊盤，握把 系列:POF MSDS 材料安全數據表:MB1102,1200, SJ5300,5400,5600,5900,6000 MSDS 產品目錄繪圖:Resilient Rollstock 標準包裝:1 系列:SJ-5900 形狀:矩形，扁平 - 可定制 顏色:黑 尺寸:卷 - 1' L x 9.000" W x 0.250" H（304.80mm x 228.60mm x 6.35mm）1/4" H 尺寸 - 可視:卷 - 1' L x 9.000" W x 0.250" H（304.80mm x 228.60mm x 6.35mm）1/4" H 材質:聚氨脂泡沫 安裝類型:膠合劑 - 丙烯酸 其它名稱:SJ5904-1FT
POF-12664-10PK 制造商:Richco 功能描述:Push On Feet; PVC (Flexible); Black; 15.7 mm; 8.6 mm; 1.3 mm; 7 mm
POF-40022 功能描述:PUSH-ON FEET BLK .31 X .06" RoHS:是 類別:硬件，緊固件，配件 >> 緩沖器，支腳，焊盤，握把 系列:POF MSDS 材料安全數據表:MB1102,1200, SJ5300,5400,5600,5900,6000 MSDS 產品目錄繪圖:Resilient Rollstock 標準包裝:1 系列:SJ-5900 形狀:矩形，扁平 - 可定制 顏色:黑 尺寸:卷 - 1' L x 9.000" W x 0.250" H（304.80mm x 228.60mm x 6.35mm）1/4" H 尺寸 - 可視:卷 - 1' L x 9.000" W x 0.250" H（304.80mm x 228.60mm x 6.35mm）1/4" H 材質:聚氨脂泡沫 安裝類型:膠合劑 - 丙烯酸 其它名稱:SJ5904-1FT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*