- 您現在的位置：買賣IC網 > PDF目錄98056 > PMP5818UWSR (ERICSSON POWER MODULES AB) 1-OUTPUT 88 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | PMP5818UWSR |
| 廠商： | ERICSSON POWER MODULES AB |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 88 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT PACKAGE-11 |
| 文件頁數： | 23/60頁 |
| 文件大?。?/td> | 4072K |
| 代理商： | PMP5818UWSR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
Ericsson Internal
PRODUCT SPECIFICATION
3 (4)
Prepared (also subject responsible if other)
No.
EWEIXIE
1/1301-BMR657 5818 Uen
Approved
Checked
Date
Rev
Reference
SEC/D (Julia You)
EMINTAO
2007-07-30
B
Safety Specification
General information
Ericsson Power Modules DC/DC converters and DC/DC regulators are
designed in accordance with safety standards IEC/EN/UL60950, Safety
of Information Technology Equipment.
IEC/EN/UL60950 contains requirements to prevent injury or damage
due to the following hazards:
Electrical shock
Energy hazards
Fire
Mechanical and heat hazards
Radiation hazards
Chemical hazards
On-board DC-DC converters and DC/DC regulators are defined as
component power supplies. As components they cannot fully comply
with the provisions of any Safety requirements without “Conditions of
Acceptability”. Clearance between conductors and between conductive
parts of the component power supply and conductors on the board in
the final product must meet the applicable Safety requirements. Certain
conditions of acceptability apply for component power supplies with
limited stand-off (see Mechanical Information for further information). It
is the responsibility of the installer to ensure that the final product
housing these components complies with the requirements of all
applicable Safety standards and Directives for the final product.
Component power supplies for general use should comply with the
requirements in IEC60950, EN60950 and UL60950 “Safety of
information technology equipment”.
There are other more product related standards, e.g. IEEE802.3af
“Ethernet LAN/MAN Data terminal equipment power”, and ETS300132-2
“Power supply interface at the input to telecommunications equipment;
part 2: DC”, but all of these standards are based on IEC/EN/UL60950
with regards to safety.
Ericsson Power Modules DC/DC converters and DC/DC regulators are
UL60950 recognized and certified in accordance with EN60950.
The flammability rating for all construction parts of the
products meets requirements for V-0 class material according to IEC
60695-11-10.
The products should be installed in the end-use equipment, in
accordance with the requirements of the ultimate application. Normally
the output of the DC/DC converter is considered as SELV (Safety Extra
Low Voltage) and the input source must be isolated by minimum Double
or Reinforced Insulation from the primary circuit (AC mains) in
accordance with IEC/EN/UL60950.
Isolated DC/DC converters
It is recommended that a slow blow fuse with a rating twice the
maximum input current per selected product be used at the input of
each DC/DC converter. If an input filter is used in the circuit the fuse
should be placed in front of the input filter.
In the rare event of a component problem in the input filter or in the
DC/DC converter that imposes a short circuit on the input source, this
fuse will provide the following functions:
Isolate the faulty DC/DC converter from the input power
source so as not to affect the operation of other parts of the
system.
Protect the distribution wiring from excessive current and
power loss thus preventing hazardous overheating.
The galvanic isolation is verified in an electric strength test.
The test voltage (Viso) between input and output is
1500 Vdc or 2250 Vdc for 60 seconds (refer to product specification).
Leakage current is less than 1 A at nominal input voltage.
24 V DC systems
The input voltage to the DC/DC converter is SELV (Safety
Extra Low Voltage) and the output remains SELV under normal and
abnormal operating conditions.
48 and 60 V DC systems
If the input voltage to the DC/DC converter is 75 Vdc or less, then the
output remains SELV (Safety Extra Low Voltage) under normal and
abnormal operating conditions.
Single fault testing in the input power supply circuit should be performed
with the DC/DC converter connected to demonstrate that the input
voltage does not exceed
75 Vdc.
If the input power source circuit is a DC power system, the source may
be treated as a TNV2 circuit and testing has demonstrated compliance
with SELV limits and isolation requirements equivalent to Basic
Insulation in accordance with IEC/EN/UL60950.
Non-isolated DC/DC regulators
The input voltage to the DC/DC regulator is SELV (Safety
Extra Low Voltage) and the output remains SELV under normal and
abnormal operating conditions.
E
PMP 5000 series
PoL Regulator
Input 4.5 - 14 V, Output up to 16 A / 88 W
EN/LZT 146 388 R1B December 2009
Ericsson AB
Technical Specication
3
相關PDF資料 |
PDF描述 |
|---|---|
| PQ1CF2 | 1.5 A SWITCHING REGULATOR, 120 kHz SWITCHING FREQ-MAX, PZFM5 |
| PQ1CF2J0000H | 1.5 A SWITCHING REGULATOR, 120 kHz SWITCHING FREQ-MAX, PZFM5 |
| PQ30033QGA30PYS | 1-OUTPUT 99.99 W DC-DC REG PWR SUPPLY MODULE |
| PQ30033QGA30NRS | 1-OUTPUT 99.99 W DC-DC REG PWR SUPPLY MODULE |
| PQ30033QGA30PKS | 1-OUTPUT 99.99 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PMP6000 | 制造商:Behringer 功能描述:20 Channel EuroPower Powered Mixing Console - 1600W 制造商:BEHRINGER 功能描述:EUROPOWER MIXING CONSOLE ACTIVE 20 CHANNEL 800W X 2 CH |
| PMP-604007 | 制造商:ADC 功能描述:ADC EIA530 GRAY KEY A 4' |
| PMP612H | 制造商:ORTRONICS 功能描述:12 PORT ETHERNET CAT 6 PATCH PANEL |
| PMP6RGT | 制造商:Carlo Gavazzi 功能描述:Electromechanical Switch Retro-Reflective Photoelectric Switch N.O./N.C. 3A Corrugated Cardboard |
| PMP6RI | 制造商:Carlo Gavazzi 功能描述: 制造商:Carlo Gavazzi 功能描述:PHOTOELECTRIC SENSOR, Sensing Range Max:6m, Output Current:3A, Sensor Output:SPS |
發(fā)布緊急采購，3分鐘左右您將得到回復。