參數資料
型號： PIC16C711-04/P
廠商： Microchip Technology
文件頁數： 38/177頁
文件大?。?/td> 0K
描述： IC MCU OTP 1KX14 A/D 18DIP
產品培訓模塊： Asynchronous Stimulus
8-bit PIC® Microcontroller Portfolio
標準包裝： 25
系列： PIC® 16C
核心處理器： PIC
芯體尺寸： 8-位
速度： 4MHz
外圍設備： 欠壓檢測/復位，POR，WDT
輸入/輸出數： 13
程序存儲器容量： 1.75KB（1K x 14）
程序存儲器類型： OTP
RAM 容量： 68 x 8
電壓 - 電源 (Vcc/Vdd)： 4 V ~ 6 V
數據轉換器： A/D 4x8b
振蕩器型： 外部
工作溫度： 0°C ~ 70°C
封裝/外殼： 18-DIP（0.300"，7.62mm）
包裝： 管件
配用： ISPICR1-ND - ADAPTER IN-CIRCUIT PROGRAMMING
309-1059-ND - ADAPTER 18 ZIF BD W/18SO PLUGS
DVA16XP180-ND - ADAPTER DEVICE FOR MPLAB-ICE
AC164010-ND - MODULE SKT PROMATEII DIP/SOIC
132
7593L–AVR–09/12
AT90USB64/128
ister. Since the OCRnx update occurs at TOP, the PWM period starts and ends at TOP. This
implies that the length of the falling slope is determined by the previous TOP value, while the
length of the rising slope is determined by the new TOP value. When these two values differ the
two slopes of the period will differ in length. The difference in length gives the unsymmetrical
result on the output.
It is recommended to use the phase and frequency correct mode instead of the phase correct
mode when changing the TOP value while the Timer/Counter is running. When using a static
TOP value there are practically no differences between the two modes of operation.
In phase correct PWM mode, the compare units allow generation of PWM waveforms on the
OCnx pins. Setting the COMnx1:0 bits to two will produce a non-inverted PWM and an inverted
PWM output can be generated by setting the COMnx1:0 to three (see Table 15-3 on page 138).
The actual OCnx value will only be visible on the port pin if the data direction for the port pin is
set as output (DDR_OCnx). The PWM waveform is generated by setting (or clearing) the OCnx
Register at the compare match between OCRnx and TCNTn when the counter increments, and
clearing (or setting) the OCnx Register at compare match between OCRnx and TCNTn when
the counter decrements. The PWM frequency for the output when using phase correct PWM can
be calculated by the following equation:
The N variable represents the prescaler divider (1, 8, 64, 256, or 1024).
The extreme values for the OCRnx Register represent special cases when generating a PWM
waveform output in the phase correct PWM mode. If the OCRnx is set equal to BOTTOM the
output will be continuously low and if set equal to TOP the output will be continuously high for
non-inverted PWM mode. For inverted PWM the output will have the opposite logic values. If
OCR1A is used to define the TOP value (WGM13:0 = 11) and COM1A1:0 = 1, the OC1A output
will toggle with a 50% duty cycle.
15.8.5
Phase and frequency correct PWM mode
The phase and frequency correct Pulse Width Modulation, or phase and frequency correct PWM
mode (WGMn3:0 = 8 or 9) provides a high resolution phase and frequency correct PWM wave-
form generation option. The phase and frequency correct PWM mode is, like the phase correct
PWM mode, based on a dual-slope operation. The counter counts repeatedly from BOTTOM
(0x0000) to TOP and then from TOP to BOTTOM. In non-inverting Compare Output mode, the
Output Compare (OCnx) is cleared on the compare match between TCNTn and OCRnx while
upcounting, and set on the compare match while downcounting. In inverting Compare Output
mode, the operation is inverted. The dual-slope operation gives a lower maximum operation fre-
quency compared to the single-slope operation. However, due to the symmetric feature of the
dual-slope PWM modes, these modes are preferred for motor control applications.
The main difference between the phase correct, and the phase and frequency correct PWM
mode is the time the OCRnx Register is updated by the OCRnx Buffer Register, (see Figure 15-
The PWM resolution for the phase and frequency correct PWM mode can be defined by either
ICRn or OCRnA. The minimum resolution allowed is 2-bit (ICRn or OCRnA set to 0x0003), and
fOCnxPCPWM
f
clk_I/O
2
NTOP
----------------------------
=
相關PDF資料
PDF描述
PIC18LF26K22-I/SP IC PIC MCU 64KB FLASH 28SPDIP
PIC18F25K80-I/SP MCU PIC 32KB FLASH 28SDIP
DSPIC33FJ12MC201-I/SS IC DSPIC MCU/DSP 12K 20SSOP
PIC16LF628-04I/P IC MCU FLASH 2KX14 COMP 18DIP
PIC16C716-04I/P IC MCU OTP 2KX14 A/D PWM 18DIP
相關代理商/技術參數
參數描述
PIC16C711-20/P 功能描述:8位微控制器 -MCU 1.75KB 68 RAM 13 I/O 20MHz PDIP18 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16C711-20/P 制造商:Microchip Technology Inc 功能描述:IC 8BIT CMOS MCU 16C711 DIP18
PIC16C711-20/SO 功能描述:8位微控制器 -MCU 1.75KB 68 RAM 13 I/O 20MHz SOIC18 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16C711-20/SO 制造商:Microchip Technology Inc 功能描述:8BIT CMOS MCU SMD 16C711 SOIC18
PIC16C711-20/SS 功能描述:8位微控制器 -MCU 1.75KB 68 RAM 13 I/O 20MHz SSOP20 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*