- 您現在的位置：買賣IC網 > PDF目錄368023 > PIC12F510_07 (Microchip Technology Inc.) 8/14-Pin, 8-Bit Flash Microcontroller PDF資料下載
參數資料
| 型號： | PIC12F510_07 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 8/14-Pin, 8-Bit Flash Microcontroller |
| 中文描述： | 8/14-Pin，8位閃存微控制器 |
| 文件頁數： | 65/116頁 |
| 文件大小： | 907K |
| 代理商： | PIC12F510_07 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁當前第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁
2007 Microchip Technology Inc.
Preliminary
DS41268C-page 63
PIC12F510/16F506
10.3.1
MCLR ENABLE
This Configuration bit, when unprogrammed (left in the
‘
1
’ state), enables the external MCLR function. When
programmed, the MCLR function is tied to the internal
V
DD
and the pin is assigned to be a I/O. See
Figure 10-7.
FIGURE 10-7:
MCLR SELECT
10.4
Power-on Reset (POR)
The PIC12F510/16F506 devices incorporate an on-
chip Power-on Reset (POR) circuitry, which provides
an internal chip Reset for most power-up situations.
The on-chip POR circuit holds the chip in Reset until
V
DD
has reached a high enough level for proper oper-
ation. The POR is active regardless of the state of the
MCLR enable bit. An internal weak pull-up resistor is
implemented using a transistor (refer to Table 13-4 for
the pull-up resistor ranges). This will eliminate external
RC components usually needed to create an external
Power-on Reset. A maximum rise time for V
DD
is spec-
ified. See
Section 13.0 “Electrical Characteristics”
for details.
When the devices start normal operation (exit the
Reset condition), device operating parameters (volt-
age, frequency, temperature,...) must be met to ensure
operation. If these conditions are not met, the devices
must be held in Reset until the operating parameters
are met.
A simplified block diagram of the on-chip Power-on
Reset circuit is shown in Figure 10-8.
The Power-on Reset circuit and the Device Reset
Timer (see
Section 10.5 “Device Reset Timer
(DRT)”
) circuit are closely related. On power-up, the
Reset latch is set and the DRT is reset. The DRT timer
begins counting once it detects MCLR, internal or
external, to be high. After the time-out period, it will
reset the Reset latch and thus end the on-chip Reset
signal.
A power-up example where MCLR is held low is shown
in Figure 10-9. V
DD
is allowed to rise and stabilize
before bringing MCLR high. The chip will actually come
out of Reset T
DRT
msec after MCLR goes high.
In Figure 10-10, the on-chip Power-on Reset feature is
being used (MCLR and V
DD
are tied together or the pin
is programmed to be (GP3/RB3). The V
DD
is stable
before the Start-up timer times out and there is no prob-
lem in getting a proper Reset. However, Figure 10-11
depicts a problem situation where V
DD
rises too slowly.
The time between when the DRT senses that MCLR is
high and when MCLR and V
DD
actually reach their full
value, is too long. In this situation, when the start-up
timer times out, V
DD
has not reached the V
DD
(min)
value and the chip may not function correctly. For such
situations, we recommend that external RC circuits be
used to achieve longer POR delay times (Figure 10-10).
For additional information, refer to Application Notes
AN522,
“Power-Up Considerations”
(DS00522) and
AN607,
“Power-up Trouble Shooting”
(DS00607).
(GP3/RB3)/MCLR/V
PP
MCLRE
Internal MCLR
GPWU/RBWU
Note:
When the devices start normal operation
(exit the Reset condition), device operat-
ing
parameters
(voltage,
temperature, etc.) must be met to ensure
operation. If these conditions are not met,
the device must be held in Reset until the
operating conditions are met.
frequency,
相關PDF資料 |
PDF描述 |
|---|---|
| PIC12F510 | 8/14-Pin, 8-Bit Flash Microcontroller |
| PIC12F519 | 8-Pin, 8-Bit Flash Microcontroller |
| PIC12F609 | 8-bit PIC㈢ Microcontrollers with High Voltage Support and Fan Control Capabilities |
| PIC12F615 | 8-bit PIC㈢ Microcontrollers with High Voltage Support and Fan Control Capabilities |
| PIC12HV609 | 8-bit PIC㈢ Microcontrollers with High Voltage Support and Fan Control Capabilities |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC12F510-E/L | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontroller |
| PIC12F510-E/LQTP | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontroller |
| PIC12F510-E/LSQTP | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontroller |
| PIC12F510E/MC | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontrollers |
| PIC12F510-E/MC | 功能描述:8位微控制器 -MCU 1.5 KB Flash 38 RAM 6 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。