- 您現在的位置：買賣IC網 > PDF目錄368023 > PIC12F510_07 (Microchip Technology Inc.) 8/14-Pin, 8-Bit Flash Microcontroller PDF資料下載
參數資料
| 型號： | PIC12F510_07 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 8/14-Pin, 8-Bit Flash Microcontroller |
| 中文描述： | 8/14-Pin，8位閃存微控制器 |
| 文件頁數： | 39/116頁 |
| 文件大?。?/td> | 907K |
| 代理商： | PIC12F510_07 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁
2007 Microchip Technology Inc.
Preliminary
DS41268C-page 37
PIC12F510/16F506
5.5
I/O Programming Considerations
5.5.1
BIDIRECTIONAL I/O PORTS
Some instructions operate internally as read followed
by write operations. For example, the
BCF
and
BSF
instructions read the entire port into the CPU, execute
the bit operation and re-write the result. Caution must
be used when these instructions are applied to a port
where one or more pins are used as input/outputs. For
example, a
BSF
operation on bit 5 of PORTB/GPIO will
cause all eight bits of PORTB/GPIO to be read into the
CPU, bit 5 to be set and the PORTB/GPIO value to be
written to the output latches. If another bit of PORTB/
GPIO is used as a bidirectional I/O pin (say bit ‘
0
’) and
it is defined as an input at this time, the input signal
present on the pin itself would be read into the CPU and
rewritten to the data latch of this particular pin, overwrit-
ing the previous content. As long as the pin stays in the
Input mode, no problem occurs. However, if bit ‘
0
’ is
switched into Output mode later on, the content of the
data latch may now be unknown.
Example 5-1 shows the effect of two sequential
Read-Modify-Write instructions (e.g.,
BCF
,
BSF
, etc.)
on an I/O port.
A pin actively outputting a high or a low should not be
driven from external devices at the same time in order
to change the level on this pin (“wired OR”, “wired
AND”). The resulting high output currents may damage
the chip.
EXAMPLE 5-1:
READ-MODIFY-WRITE
INSTRUCTIONS ON AN
I/O PORT(e.g., PIC16F506)
5.5.2
SUCCESSIVE OPERATIONS ON I/O
PORTS
The actual write to an I/O port happens at the end of an
instruction cycle. Whereas for reading, the data must
be valid at the beginning of the instruction cycle
(Figure 5-14). Therefore, care must be exercised if a
write followed by a read operation is carried out on the
same I/O port. The sequence of instructions should
allow the pin voltage to stabilize (load dependent)
before the next instruction causes the file to be read
into the CPU. Otherwise, the previous state of that pin
may be read into the CPU rather than the new state.
When in doubt, it is better to separate these
instructions with a
NOP
or another instruction not
accessing this I/O port.
FIGURE 5-14:
SUCCESSIVE I/O OPERATION (PIC16F506)
;Initial PORTB Settings
;PORTB<5:3> Inputs
;PORTB<2:0> Outputs
;
;
;
BCF
PORTB, 5 ;--01 -ppp
BCF
PORTB, 4 ;--10 -ppp
MOVLW
007h;
TRIS
PORTB
;
PORTB latch
----------
PORTB pins
----------
--11 pppp
--11 pppp
;--10 -ppp
--11 pppp
Note:
The user may have expected the pin values to
be ‘
--00 pppp
’. The 2nd
BCF
caused RB5 to
be latched as the pin value (High).
PC
PC + 1
PC + 2
PC + 3
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
Q1
Q2 Q3 Q4
Q1 Q2
Q3 Q4
Instruction
Fetched
RB<5:0>
MOVWF PORTB
NOP
Port pin
sampled here
NOP
MOVF PORTB, W
Instruction
Executed
MOVWF PORTB
(Write to PORTB)
NOP
MOVF PORTB,W
(Read PORTB)
This example shows a write to PORTB followed by a
read from PORTB.
Data setup time = (0.25 T
CY
– T
PD
)
where: T
CY
= instruction cycle
T
PD
= propagation delay
Therefore, at higher clock frequencies, a
write followed by a read may be problematic.
Port pin
written here
相關PDF資料 |
PDF描述 |
|---|---|
| PIC12F510 | 8/14-Pin, 8-Bit Flash Microcontroller |
| PIC12F519 | 8-Pin, 8-Bit Flash Microcontroller |
| PIC12F609 | 8-bit PIC㈢ Microcontrollers with High Voltage Support and Fan Control Capabilities |
| PIC12F615 | 8-bit PIC㈢ Microcontrollers with High Voltage Support and Fan Control Capabilities |
| PIC12HV609 | 8-bit PIC㈢ Microcontrollers with High Voltage Support and Fan Control Capabilities |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC12F510-E/L | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontroller |
| PIC12F510-E/LQTP | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontroller |
| PIC12F510-E/LSQTP | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontroller |
| PIC12F510E/MC | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontrollers |
| PIC12F510-E/MC | 功能描述:8位微控制器 -MCU 1.5 KB Flash 38 RAM 6 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。