- 您現在的位置：買賣IC網 > PDF目錄368023 > pic12ce674 (Microchip Technology Inc.) 8-Pin, 8-Bit CMOS Microcontroller with A/D Converter(具A/D轉換器和EEPROM數據存儲器的8位微控制器) PDF資料下載
參數資料
| 型號： | pic12ce674 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 8-Pin, 8-Bit CMOS Microcontroller with A/D Converter(具A/D轉換器和EEPROM數據存儲器的8位微控制器) |
| 中文描述： | 8引腳，8位CMOS微控制器與A / D轉換器（具的A / D轉換器和EEPROM的數據存儲器的8位微控制器） |
| 文件頁數： | 59/112頁 |
| 文件大?。?/td> | 1205K |
| 代理商： | PIC12CE674 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁當前第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁
1998 Microchip Technology Inc.
Preliminary
DS40181A-page 59
PIC12CE67X
FIGURE 9-18: WAKE-UP FROM SLEEP THROUGH INTERRUPT
Q1
Q2
Q3 Q4
Q1 Q2
Q3
Q4
Q1
Q1
Q2 Q3 Q4
Q1 Q2 Q3 Q4
Q1
Q2 Q3
Q4
Q1 Q2
Q3
Q4
OSC1
CLKOUT(4)
GPIO pin
GPIF flag
GIE bit
INSTRUCTION FLOW
PC
Instruction
Instruction
PC
PC+1
PC+2
Inst(PC) = SLEEP
Inst(PC - 1)
Inst(PC + 1)
SLEEP
Processor in
SLEEP
Interrupt Latency
(Note 2)
Inst(PC + 2)
Inst(PC + 1)
Inst(0004h)
Inst(0005h)
Inst(0004h)
Dummy cycle
PC + 2
0004h
0005h
Dummy cycle
T
OST
(2)
PC+2
Note
1:
2:
3:
4:
XT, HS or LP oscillator mode assumed.
T
OST
= 1024T
OSC
(drawing not to scale) This delay will not be there for INTRC and EXTRC osc mode.
GIE = '1' assumed. In this case after wake- up, the processor jumps to the interrupt routine. If GIE = '0', execution will continue in-line.
CLKOUT is not available in XT, HS or LP osc modes, but shown here for timing reference.
9.9
If the code protection bit(s) have not been pro-
grammed, the on-chip program memory can be read
out for verification purposes.
Program Verification/Code Protection
9.10
Four memory locations (2000h - 2003h) are designated
as ID locations where the user can store checksum or
other code-identification numbers. These locations are
not accessible during normal execution but are read-
able and writable during program/verify. It is recom-
mended that only the 4 least significant bits of the ID
location are used.
ID Locations
9.11
PIC12CE67X microcontrollers can be serially pro-
grammed while in the end application circuit. This is
simply done with two lines for clock and data, and three
other lines for power, ground, and the programming
voltage. This allows customers to manufacture boards
with unprogrammed devices, and then program the
microcontroller just before shipping the product. This
also allows the most recent firmware or a custom firm-
ware to be programmed.
The device is placed into a program/verify mode by
holding the GP1 and GP0 pins low while raising the
MCLR (V
PP
) pin from V
IL
to V
IHH
(see programming
specification). GP1 (clock) becomes the programming
clock and GP0 (data) becomes the programming data.
Both GP0 and GP1 are Schmitt Trigger inputs in this
mode.
In-Circuit Serial Programming
Note:
Microchip does not recommend code pro-
tecting windowed devices.
After reset, to place the device into programming/verify
mode, the program counter (PC) is at location 00h. A 6-
bit command is then supplied to the device. Depending
on the command, 14-bits of program data are then sup-
plied to or from the device, depending if the command
was a load or a read. For complete details of serial pro-
gramming, please refer to the PIC12CE67X Program-
ming Specifications.
FIGURE 9-19: TYPICAL IN-CIRCUIT SERIAL
PROGRAMMING
CONNECTION
External
Connector
Signals
To Normal
Connections
To Normal
Connections
PIC12CE67X
V
DD
V
SS
MCLR/V
PP
GP1
GP0
+5V
0V
V
PP
CLK
Data I/O
V
DD
相關PDF資料 |
PDF描述 |
|---|---|
| PIC12CR509A | 8-Pin, 8-Bit CMOS Microcontrollers |
| PIC12F505 | 8/14-Pin, 8-Bit Flash Microcontrollers |
| PIC12F506 | 8/14-Pin, 8-Bit Flash Microcontroller |
| PIC12F510_07 | 8/14-Pin, 8-Bit Flash Microcontroller |
| PIC12F510 | 8/14-Pin, 8-Bit Flash Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC12CE674/JW | 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 6 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC12CE674-04/JM | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin, 8-Bit CMOS Microcontroller with A/D Converter |
| PIC12CE674-04/JW | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin, 8-Bit CMOS Microcontroller with A/D Converter and EEPROM Data Memory |
| PIC12CE674-04/P | 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 6 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC12CE674-04/P | 制造商:Microchip Technology Inc 功能描述:IC 8BIT CMOS MCU 12CE674 DIP8 |
發布緊急采購，3分鐘左右您將得到回復。