- 您現在的位置：買賣IC網 > PDF目錄11744 > PI7C8150BNDE (Pericom)IC PCI-PCI BRIDGE ASYNC 256-PBGA PDF資料下載
參數資料
| 型號： | PI7C8150BNDE |
| 廠商： | Pericom |
| 文件頁數： | 40/109頁 |
| 文件大小： | 0K |
| 描述： | IC PCI-PCI BRIDGE ASYNC 256-PBGA |
| 標準包裝： | 90 |
| 系列： | * |
| 應用： | * |
| 接口： | * |
| 電源電壓： | * |
| 封裝/外殼： | 256-BGA |
| 供應商設備封裝： | 256-PBGA（17x17） |
| 包裝： | 管件 |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁
PI7C8150B
ASYNCHRONOUS 2-PORT PCI-TO-PCI BRIDGE
ADVANCE INFORMATION
Page 36 of 109
April 2009 – Revision 1.08
For burst transfer, with the exception of “Memory Write and Invalidate” transactions,
the master latency timer expires and the PI7C8150B’s bus grant is de-asserted.
The target terminates the transaction with a retry, disconnect, or target abort.
If PI7C8150B is delivering posted write data when it terminates the transaction because the
master latency timer expires, it initiates another transaction to deliver the remaining write
data. The address of the transaction is updated to reflect the address of the current DWORD
to be delivered.
If PI7C8150B is pre-fetching read data when it terminates the transaction because the
master latency timer expires, it does not repeat the transaction to obtain more data.
3.8.2
MASTER ABORT RECEIVED BY PI7C8150B
If the initiator initiates a transaction on the target bus and does not detect DEVSEL_L
returned by the target within five clock cycles of the assertion of FRAME_L, PI7C8150B
terminates the transaction with a master abort. This sets the received-master-abort bit in the
status register corresponding to the target bus.
For delayed read and write transactions, PI7C8150B is able to reflect the master abort
condition back to the initiator. When PI7C8150B detects a master abort in response to a
delayed transaction, and when the initiator repeats the transaction, PI7C8150B does not
respond to the transaction with DEVSEL_L, which induces the master abort condition back
to the initiator. The transaction is then removed from the delayed transaction queue. When
a master abort is received in response to a posted write transaction, PI7C8150B discards
the posted write data and makes no more attempts to deliver the data. PI7C8150B sets the
received-master-abort bit in the status register when the master abort is received on the
primary bus, or it sets the received master abort bit in the secondary status register when
the master abort is received on the secondary interface. When master abort is detected in
posted write transaction with both master-abort-mode bit (bit 5 of bridge control register)
and the SERR_L enable bit (bit 8 of command register for secondary bus) are set,
PI7C8150B asserts P_SERR_L if the master-abort-on-posted-write is not set. The master-
abort-on-posted-write bit is bit 4 of the P_SERR_L event disable register (offset 64h).
Note: When PI7C8150B performs a Type 1 to special cycle conversion, a master abort is
the expected termination for the special cycle on the target bus. In this case, the master
abort received bit is not set, and the Type 1 configuration transaction is disconnected after
the first data phase.
3.8.3
TARGET TERMINATION RECEIVED BY PI7C8150B
When PI7C8150B initiates a transaction on the target bus and the target responds with
DEVSEL_L, the target can end the transaction with one of the following types of
termination:
Normal termination (upon de-assertion of FRAME_L)
Target retry
相關PDF資料 |
PDF描述 |
|---|---|
| V300A15E500B3 | CONVERTER MOD DC/DC 15V 500W |
| DSPIC33FJ64MC202-E/MM | IC DSPIC MCU/DSP 64K 28-QFN |
| PI7C8150AMAE | IC PCI-PCI BRIDGE 2PORT 208-FQFP |
| PIC18F2515-I/SP | IC MCU FLASH 24KX16 28-DIP |
| V300A15E500B2 | CONVERTER MOD DC/DC 15V 500W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PI7C8150BNDI | 功能描述:外圍驅動器與原件 - PCI 2-Port 32-Bit PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PI7C8150BNDI-33 | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:ASYNCHRONOUS 2-PORT PCI-TO-PCI BRIDGE |
| PI7C8150BNDIE | 功能描述:外圍驅動器與原件 - PCI 2 Port 32B PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PI7C8150BNDIE-33 | 功能描述:外圍驅動器與原件 - PCI 2 Port 32B PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PI7C8150DMAE | 功能描述:外圍驅動器與原件 - PCI 2-Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。