- 您現在的位置：買賣IC網 > PDF目錄367820 > PCF8833U (NXP Semiconductors N.V.) STN RGB - 132 X 132 X 3 driver PDF資料下載
參數資料
| 型號： | PCF8833U |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | STN RGB - 132 X 132 X 3 driver |
| 中文描述： | 超扭曲的RGB - 132 × 132 × 3驅動程序 |
| 文件頁數： | 84/112頁 |
| 文件大?。?/td> | 469K |
| 代理商： | PCF8833U |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁當前第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁
2003 Feb 14
84
Philips Semiconductors
Objective specification
STN RGB - 132
×
132
×
3 driver
PCF8833
handbook, full pagewidth
MGU972
INTERFACE
INTERFACE
REGISTERS
e.g. SLA[2:0]
0
to temperature
compensation circuit
OTP CELL
EFD
default = 0
INTERFACE
SFD
default = 1
OTP DEFAULTS
e.g. SLA[2:0]
OR
1
Fig.56 Factory defaults.
15.3
Seal bit
The module maker programming is performed in the
Calibration mode. This mode is entered via a special
interface command (CALMM). To prevent erroneous
programming, a seal bit has been implemented which
prevents the device from entering Calibration mode. This
seal bit, once programmed, cannot be reversed, thus
further changes in programmed values are not possible.
Applying the programming voltage when not in CALMM
mode will have no effect on the programmed values.
Table 89
Seal bit definition
15.4
OTP architecture
An OTP cell is divided into a non-volatile programmable
instance containing the value and a register, where the
value is made accessible to the rest of the chip.
In the PCF8833 104 OTP cells are available for the
module maker. These cells are organised in a matrix of
7 rows and 15 columns, where the last row is only partially
used; see Table 90. All the rows of one particular column
of the matrix are filled in parallel by sending 1 byte of data
with the OTPSHTIN command. Byte 15 is sent first
(containing PVB[3:0], BRS and TRS) and byte 0 last
(containing MMVOP[5:0] or SEAL).
Bit 7 of every data byte is not used. An example sequence
on how to fill the matrix is given in Table 96.
The default value of the OTP cells is shown in Table 91.
These values may be changed by programming the OTP
cell. The programming of a cell will invert the default value.
This inversion may only happen once per cell, as the
programming is irreversible.
Table 93 shows an example on how to program the OTP
cells to receive the values given in Table 92. Some
examples are given below:
1.
The default for DFA[0] is 0; see Table 91, and it is
required to have DFA[0] = 1; see Table 92. This
means that the value needs to be inverted. Therefore
the OTP cell has to be programmed (a 1 in Table 93).
2.
The default for DFA[4] is 1; see Table 91, and it is
required to have DFA[4] = 0; see Table 92. This
means that the value needs to be inverted. Therefore
the OTP cell has to be programmed (a 1 in Table 93).
3.
The default for DFA[5] is 1; see Table 91, and it is
required to have DFA[5] = 1; see Table 92. This
means that it is not necessary to change the value.
Therefore it is not necessary to program the OTP cell
(a 0 in Table 93).
4.
The default for DFA[6] is 0; see Table 91, and it is
required to have DFA[6] = 0; see Table 92. This
means that it is not necessary to change the value.
Therefore it is not necessary to program the OTP cell
(a 0 in Table 93).
SEAL BIT
ACTION
0
1
Calibration mode enabled
Calibration mode disabled
相關PDF資料 |
PDF描述 |
|---|---|
| PCF8881 | 132 x 132 RGB single chip TFT driver with DC-to-DC converter |
| PCI-ADC | MULTIFUNKTIONSKARTE 44 KANAL PCI BUS |
| PCI-DIO | KARTE E/A 32 KANAL PCI BUS |
| PCI-NT | TREIBER SOFTWARE FUER PCI E/A KARTEN |
| PCI-PIO | KARTE E/A 48 KANAL PCI BUS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCF8833U/2DA | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:STN RGB - 132 X 132 X 3 driver |
| PCF8881 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:132 x 132 RGB single chip TFT driver with DC-to-DC converter |
| PCF8881U/2DA | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:132 x 132 RGB single chip TFT driver with DC-to-DC converter |
| PCF8883 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Capacitive proximity switch with auto-calibration, large voltage operating range and very low power consumption |
| PCF8883_11 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Capacitive proximity switch with auto-calibration, large voltage operating |
發布緊急采購，3分鐘左右您將得到回復。