- 您現在的位置：買賣IC網 > PDF目錄367820 > PCF8583 (NXP SEMICONDUCTORS) Clock/calendar with 240×8-bit RAM(帶240×8位RAM的時鐘/日歷) PDF資料下載
參數資料
| 型號： | PCF8583 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | XO, clock |
| 英文描述： | Clock/calendar with 240×8-bit RAM(帶240×8位RAM的時鐘/日歷) |
| 中文描述： | REAL TIME CLOCK |
| 文件頁數： | 11/28頁 |
| 文件大?。?/td> | 162K |
| 代理商： | PCF8583 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
1997 Jul 15
11
Philips Semiconductors
Product specification
Clock/calendar with 240
×
8-bit RAM
PCF8583
Fig.9 Selection of alarm weekdays.
handbook, full pagewidth
7
6
5
4
3
2
1
0
MSB
LSB
MRB006
memory location 0E (alarm weekday / month)
weekday 0 enabled when set
weekday 1 enabled when set
weekday 2 enabled when set
weekday 3 enabled when set
weekday 4 enabled when set
weekday 5 enabled when set
weekday 6 enabled when set
not used
7.7
Timer
The timer (location 07) is enabled by setting the
control/status register = XX0X X1XX. The timer counts up
from 0 (or a programmed value) to 99. On overflow, the
timer resets to 0. The timer flag (LSB of control/status
register) is set on overflow of the timer. This flag must be
reset by software. The inverted value of this flag can be
transferred to the external interrupt by setting bit 3 of the
alarm control register.
Additionally, a timer alarm can be programmed by setting
the timer alarm enable (bit 6 of the alarm control register).
When the value of the timer equals a pre-programmed
value in the alarm timer register (location 0F), the alarm
flag is set (bit 1 of the control/status register). The inverted
value of the alarm flag can be transferred to the external
interrupt by enabling the alarm interrupt (bit 6 of the alarm
control register).
Resolution of the timer is programmed via the 3 LSBs of
the alarm control register (see Fig.11, Alarm and timer
Interrupt logic diagram).
7.8
Event counter mode
Event counter mode is selected by bits 4 and 5 which are
logic 1, 0 in the control/status register. The event counter
mode is used to count pulses externally applied to the
oscillator input (OSCO left open-circuit).
The event counter stores up to 6 digits of data, which are
stored as 6 hexadecimal values located in locations 1, 2,
and 3. Thus, up to 1 million events may be recorded.
An event counter alarm occurs when the event counter
registers match the value programmed in locations 9, A,
and B, and the event alarm is enabled (bits 4 and 5 which
are logic 0, 1 in the alarm control register). In this event,
the alarm flag (bit 1 of the control/status register) is set.
The inverted value of this flag can be transferred to the
interrupt pin (pin 7) by setting the alarm interrupt enable in
the alarm control register. In this mode, the timer
(location 07) increments once for every one, one-hundred,
ten thousand, or 1 million events, depending on the value
programmed in bits 0, 1 and 2 of the alarm control register.
In all other events, the timer functions are as in the clock
mode.
7.9
Interrupt output
The conditions for activating the open-drain n-channel
interrupt output INT (active LOW) are determined by
appropriate programming of the alarm control register.
These conditions are clock alarm, timer alarm, timer
overflow, and event counter alarm. An interrupt occurs
when the alarm flag or the timer flag is set, and the
corresponding interrupt is enabled. In all events, the
interrupt is cleared only by software resetting of the flag
which initiated the interrupt.
相關PDF資料 |
PDF描述 |
|---|---|
| PCF8584 | IIC-bus controller(IIC總線控制器) |
| PCF8593 | Low power clock/calendar(低功耗時鐘/日歷) |
| PCF8801 | CRYSTAL RESONATOR, 6MHZ |
| PCF8801U | LCD driver for 140 x 2 segments |
| PCF8811 | 80 x 128 pixels matrix LCD driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCF8583BS | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Clock and calendar with 240 x 8-bit RAM |
| PCF8583BS,518 | 功能描述:實時時鐘 CLOCK CALENDAR W RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| PCF8583BS-T | 功能描述:實時時鐘 CLOCK CALENDAR W 256X8SRAM I2C RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| PCF8583P | 制造商:NXP Semiconductors 功能描述:Clock/Calendar/Alarm/Timer/Interrupt Serial (2-Wire, I2C) 制造商:NXP Semiconductors 功能描述:IC CLOCK CALENDAR/SRAM 8583 DIP8 制造商:NXP Semiconductors 功能描述:IC, CLOCK CALENDAR/SRAM, 8583, DIP8 制造商:NXP Semiconductors 功能描述:Clock/calendar with 2408-bit RAM |
| PCF8583P/F5 | 制造商:NXP Semiconductors 功能描述:Real Time Clock Serial 240Byte 8-Pin PDIP Tube |
發布緊急采購，3分鐘左右您將得到回復。