- 您現在的位置：買賣IC網 > PDF目錄382379 > PCA9560 (NXP Semiconductors N.V.) The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each PDF資料下載
參數資料
| 型號： | PCA9560 |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | DRAM |
| 英文描述： | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| 中文描述： | 該CAT24FC02是一個2 KB的EEPROM的國內256個8位每字舉辦的串行CMOS |
| 文件頁數： | 7/17頁 |
| 文件大小： | 111K |
| 代理商： | PCA9560 |
Philips Semiconductors
Product data
PCA9560
Dual 5-bit multiplexed 1-bit latched
I
2
C EEPROM DIP switch
2003 Jun 27
7
CHARACTERISTICS OF THE I
2
C-BUS
The I
2
C-bus is for 2-way, 2-line communication between different ICs or modules. The two lines are a serial data line (SDA) and a serial clock line
(SCL). Both lines must be connected to a positive supply via a pull-up resistor when connected to the output stages of a device. Data transfer may
be initiated only when the bus is not busy.
Bit transfer
One data bit is transferred during each clock pulse. The data on the SDA line must remain stable during the HIGH period of the clock pulse as
changes in the data line at this time will be interpreted as control signals (see Figure 5).
SDA
SCL
SW00363
data line
stable;
data valid
change
of data
allowed
Figure 5. Bit transfer
Start and stop conditions
Both data and clock lines remain HIGH when the bus is not busy. A HIGH-to-LOW transition of the data line, while the clock is HIGH is defined
as the start condition (S). A LOW-to-HIGH transition of the data line while the clock is HIGH is defined as the stop condition (P) (see Figure 6).
System configuration
A device generating a message is a
‘
transmitter
’
, a device receiving is the
‘
receiver
’
. The device initiates a transfer is the
‘
master
’
and the
devices which are controlled by the master are the
‘
slaves
’
(see Figure 7).
SDA
SCL
SW00365
S
P
SDA
SCL
START condition
STOP condition
Figure 6. Definition of start and stop conditions
MASTER
TRANSMITTER/
RECEIVER
SLAVE
RECEIVER
SLAVE
TRANSMITTER/
RECEIVER
MASTER
TRANSMITTER
MASTER
TRANSMITTER/
RECEIVER
SDA
SCL
SW00366
I
2
C
MULTIPLEXER
SLAVE
Figure 7. System configuration
相關PDF資料 |
PDF描述 |
|---|---|
| PCA9560D | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| PCB2032V | EEPROM |
| PCB2320DP | ISDN Line Interface |
| PCB2325DP | ISDN Line Interface |
| PCB2391A | ISDN， Other/Special/Miscellaneous |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9560D | 功能描述:電可擦除可編程只讀存儲器 DUAL5BTMUX 1B LATCH I2C EPROM RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| PCA9560D,112 | 功能描述:多路器開關 IC DUAL5BTMUX 1B LATCH RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| PCA9560D,118 | 功能描述:多路器開關 IC DUAL5BTMUX 1B LATCH RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| PCA9560D-T | 功能描述:電可擦除可編程只讀存儲器 DUAL5BTMUX 1B LATCH I2C EPROM RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| PCA9560PW | 功能描述:電可擦除可編程只讀存儲器 DUAL5BTMUX 1B LATCH I2C EPROM RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。