- 您現在的位置：買賣IC網 > PDF目錄382368 > P82C150AFT (NXP SEMICONDUCTORS) CAN Serial Linked I/O device SLIO with digital and analog port functions PDF資料下載
參數資料
| 型號： | P82C150AFT |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | CAN Serial Linked I/O device SLIO with digital and analog port functions |
| 中文描述： | 1 CHANNEL(S), 125K bps, LOCAL AREA NETWORK CONTROLLER, PDSO28 |
| 封裝： | 7.50 MM, PLASTIC, SO-28 |
| 文件頁數： | 11/36頁 |
| 文件大小： | 209K |
| 代理商： | P82C150AFT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
1996 Jun 19
11
Philips Semiconductors
Preliminary specification
CAN Serial Linked I/O device (SLIO) with
digital and analog port functions
P82C150
7.2.6
A
NALOG
C
ONFIGURATION
R
EGISTER
(A
DDRESS
5)
This read/write register contains the bits ADC, OC3 to
OC1, M3 to M1 and SW3 to SW1 (see Fig.7).
ADC bit (analog-to-digital conversion start bit; write only
bit). The P82C150 starts an analog-to-digital conversion
cycle at ADC = 1 ended with the transmission of a
message containing the result. After that, the ADC bit is
reset automatically.
OC3 to OC1 bits (comparator output data; read only
bits). The bits OC3 to OC1 represent the logical output
level of the analog comparators at input port pins P10,
P11, P12, P13 and P15. The P82C150 sends back the
logical output value of these comparators after having
received a Data Frame (see Section 7.3.3) addressing
the Analog Configuration Register. The comparator
outputs can be monitored at the output port pins P8, P9
and P7.
M3 to M1 bits (multiplexer control bits; write only bits).
The logical value of the comparators is monitored on
port pins P8, P9 and P7 (see Fig.7) by setting M3 to M1
to logic 1, provided that these pins are configured as
outputs (OE = 1). Additionally the register content is
sent automatically when the corresponding port bits in
the Positive Edge Register and/or Negative Edge
Register and the corresponding bits in the Output
Enable Register are set.
SW3 to SW1 (analog switch control bits; write only bits).
One of the analog switches S1 to S6 can be closed by
setting the switch bits to the corresponding value
(see Fig.7 and Table 4).
Table 4
Analog switch selection by SW3, SW2, SW1.
Note
1.
Evidently if P14 is driven, it may not be connected to
any other driven pin via the internal analog switches
(avoid short-circuit!).
SW3
SW2
SW1
SWITCH STATE
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
no switch closed (S0); note 1
S1 closed
S2 closed
S3 closed
S4 closed
S5 closed
S6 closed
reserved
7.2.7
DPM1 R
EGISTER
(A
DDRESS
6)
This write only register contains data for a quasi-analog
output signal on port pin P10, which is generated by
Distributed Pulse Modulation (DPM; see Fig.9).
The Output Enable bit must be set for this functions
(OE10 = 1). The DPM1 output signal is inverted by setting
DO10 = 1. The number of output pulses during a DPM
period is given by the DPM1 Register value. These pulses
have 4
×
t
CLK
length and are distributed over the DPM
period. An analog voltage is provided after smoothing the
output signal by an external RC combination.
7.2.8
DPM2 R
EGISTER
(A
DDRESS
7)
This write only register contains data for a quasi-analog
output signal on port pin P4. The function of the DPM2
corresponds to the definition of DPM1.
7.2.9
A
NALOG-TO-
D
IGITAL
C
ONVERSION
(ADC)
R
EGISTER
(A
DDRESS
8)
This read only register contains the result of the
analog-to-digital converted level of that I/O pin which was
selected by the SW bits. The conversion is started by
ADC-bit set to logic 1 (see Section 7.2.6), or by
transmitting a Data Frame addressing the ADC Register.
相關PDF資料 |
PDF描述 |
|---|---|
| P82C150AHT | 22 PIN R/A MALE PRESSFIT ATCA ZONE 1 CON |
| P82C605 | System Controller |
| P82C606 | System Controller |
| P82C607 | Peripheral IC |
| P82C611 | Micro Channel Bus Interface/Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P82C150AHT | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:CAN Serial Linked I/O device SLIO with digital and analog port functions |
| P82C201-10 | 制造商:CHIPS 功能描述: 制造商:CHIP 功能描述:SYSTEM CONTROLLER, 84 Pin, PLCC 制造商:CHIPS 功能描述:SYSTEM CONTROLLER, 84 Pin, PLCC |
| P82C201-10 TS89 | 制造商:TOS 功能描述:82C201-10 |
| P82C201-10-7014-0093 | 制造商:CHIPS 功能描述: |
| P82C20110TS89 | 制造商:TOS 功能描述:82C201-10 |
發布緊急采購，3分鐘左右您將得到回復。