- 您現在的位置：買賣IC網 > PDF目錄384799 > OV6120 (Electronic Theatre Controls, Inc.) SINGLE-CHIP CMOS CIF COLOR DIGITAL CAMERA PDF資料下載
參數資料
| 型號： | OV6120 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | SINGLE-CHIP CMOS CIF COLOR DIGITAL CAMERA |
| 中文描述： | 單芯片CMOS到岸價格彩色數碼攝像機 |
| 文件頁數： | 14/31頁 |
| 文件大?。?/td> | 341K |
| 代理商： | OV6120 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
OV6620/OV6120
14
Version 1.11
14 May 1999
SINGLE IC CMOS COLOR AND B/W DIGITAL CAMERAS
O
MNI
V
ISION
T
ECHNOLOGIES
, Inc.
Advanc ed Information
Preliminary
1.2.7
The OV6620/OV6120 sensors can be programmable to
operate in slave mode configuration (COMI[6] = 1, de-
fault is master mode). HSYNC and VSYNC output sig-
nals are provided.
When used as a slave device, the external master must
provide the OV6620/OV6120 imager with the following:
Slave Mode Operation
1. System clock CLK to XCLK1 pin;
2. Horizontal sync, Hsync, to CHSYNC pin, positive
assertion;
3. Vertical frame sync, Vsync, to VSYNC
pin,
positive assertion
When in slave mode, the OV6620/OV6120 tri-states
CHSYNC (pin 42) and VSYNC (pin 16) output pins,
which may then be used as input pins. To synchronize
multiple devices, the OV6620/OV6120 image sensors
use external system clock, CLK, to synchronize external
horizontal sync, HSYNC, which is then used to synchro-
nize external vertical frame sync, Vsync. See Figure 5,
Slave Mode External Sync Timing for timing consider-
ations.
1.2.8
The OV6620/OV6120 sensors support frame exposure
mode when programmed for Progressive Scan. FREX
(pin 4) is asserted by an external master device to set
exposure time. When FREX = 1, the OV6620/OV6120
pixel array will be quickly precharged. Based on the ex-
ternal master’s assertion of FREX, the OV6620/OV6120
devices capture the image. When the master de-asserts
FREX (FREX = 0), the video output data stream is deliv-
ered to the OV6620/OV6120 output port in a line-by-line
manner.
It should be noted that FREX must active long enough
to ensure the complete image array has been pre-
charged.
When data is being output from the OV6620/OV6120
image sensor, care must be taken so as not to expose
the image array to light. This may affect the integrity of
the image data captured. A mechanical shutter synchro-
nized with the frame exposure rate can be used to min-
imize this situation. Frame exposure mode timing is
shown in Section Figure 6. Frame Exposure Timing be-
low.
Frame Exposure Mode
1.2.9
The OV6620/OV6120 image sensor includes a RESET
pin (pin 2) which forces a complete hardware reset when
Reset
pulled high (Vcc). When a hardware reset occurs, the
OV6620/OV6120 sensor clears all registers or sets
them to their default values. Reset may also be initiated
through the I
2
C interface.
1.2.10 Power Down Mode
Two methods are available for placing the OV6620/
OV6120 devices into power-down mode: hardware pow-
er down and I
2
C/software power down.
To initiate hardware power down the PWDN pin (pin 9)
must be tied to high (+5VDC). When this occurs, the
OV6620/OV6120 internal device clock is halted and all
internal registers (except I
2
C registers) are reset. In this
mode, current draw is less than 10uA.
Executing a software power down through the I
2
C inter-
face suspends internal circuit activity, but does halt the
device clock. In this mode, current requirements drop to
less than 1mA.
1.2.11 Configuring the OV6620/OV6120 Image
Sensors
Two methods are provided for configuring the OV6620/
OV6120 IC for specific application requirements.
At power up, the OV6620/OV6120 sensor reads the sta-
tus of certain pins to determine what, if any, power up
default settings are requested. Once the reading of the
external pins is completed, the device configures its in-
ternal registers according to the specified pins. Not all
device functions are available for configuration through
external pin.
A more flexible and comprehensive method for configur-
ing the OV6620/OV6120 IC is to use its on-chip I
2
C reg-
ister programming capability. The I
2
C interface provides
access to all of the device’s programmable internal reg-
isters. See Section 3.1 I
2
C Bus Protocol Format for fur-
ther details about using the I
2
C interface on the
OV6620/OV6120 camera device.
相關PDF資料 |
PDF描述 |
|---|---|
| OV6620 | SINGLE-CHIP CMOS CIF COLOR DIGITAL CAMERA |
| OV6130 | SINGLE-CHIP CMOS CIF COLOR DIGITAL CAMERA |
| OV6630 | SINGLE-CHIP CMOS CIF COLOR DIGITAL CAMERA |
| OV7410 | SINGLE-CHIP CMOS COLOR PAL CAMERA |
| OV7410P | SINGLE-CHIP CMOS COLOR PAL CAMERA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OV6130 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SINGLE-CHIP CMOS CIF COLOR DIGITAL CAMERA |
| OV6620 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SINGLE-CHIP CMOS CIF COLOR DIGITAL CAMERA |
| OV6630 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SINGLE-CHIP CMOS CIF COLOR DIGITAL CAMERA |
| OV6680 | 制造商:OMNIVISION 制造商全稱:OMNIVISION 功能描述:optimal low-light sensitivity and pixel performance for video conferencing cameras in 3G mobile phones |
| OV7121 | 制造商:Omnivision Technologies Inc 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。