- 您現在的位置：買賣IC網 > PDF目錄299576 > OR3T125-4PS208I FPGA, 784 CLBS, 92000 GATES, 80 MHz, PQFP208 PDF資料下載
參數資料
| 型號： | OR3T125-4PS208I |
| 元件分類： | FPGA |
| 英文描述： | FPGA, 784 CLBS, 92000 GATES, 80 MHz, PQFP208 |
| 封裝： | SQFP-208 |
| 文件頁數： | 158/210頁 |
| 文件大小： | 2138K |
| 代理商： | OR3T125-4PS208I |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁當前第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁
Lucent Technologies Inc.
51
Preliminary Data Sheet, Rev. 1
September 1998
ORCA Series 3 FPGAs
Special Function Blocks
Special function blocks in the Series 3 provide extra
capabilities beyond general FPGA operation. These
blocks reside in the corners and MIDs (middle inter-
quad areas) of the FPGA array.
Single Function Blocks
Most of the special function blocks perform a specific
dedicated function. These functions are data/configura-
tion readback control, global 3-state control (TS_ALL),
internal oscillator generation, global set/reset (GSRN),
and start-up logic.
Readback Logic
The readback logic is located in the upper right corner
of the FPGA and can be enabled via a bit stream
option or by instantiation of a library readback compo-
nent.
Readback is used to read back the configuration data
and, optionally, the state of the PFU outputs. A read-
back operation can be done while the FPGA is in nor-
mal system operation. The readback operation cannot
be daisy-chained. To use readback, the user selects
options in the bit stream generator in the
ORCA
Foundry Development System.
Table 12 provides readback options selected in the bit
stream generator tool. The table provides the number
of times that the configuration data can be read back.
This is intended primarily to give the user control over
the security of the FPGA’s configuration program. The
user can prohibit readback (0), allow a single readback
(1), or allow unrestricted readback (U).
Readback can be performed via the Series 3 micropro-
cessor interface (MPI) or by using dedicated FPGA
readback controls. If the MPI is enabled, readback via
the dedicated FPGA readback logic is disabled. Read-
back using the MPI is discussed in the Microprocessor
Interface (MPI) section.
The pins used for dedicated readback are readback
data (RD_DATA), read configuration (RD_CFG), and
configuration clock (CCLK). A readback operation is
initiated by a high-to-low transition on RD_CFG. The
RD_CFG
input must remain low during the readback
operation. The readback operation can be restarted at
frame 0 by driving the RD_CFG pin high, applying at
least two rising edges of CCLK, and then driving
RD_CFG
low again. One bit of data is shifted out on
RD_DATA at the rising edge of CCLK. The first start bit
of the readback frame is transmitted out several cycles
after the first rising edge of CCLK after RD_CFG is input
low (see the Readback Timing Characteristics table in
the Timing Characteristics section). To be certain of the
start of the readback frame, the data can be monitored
for the 01 frame start bit pair.
Readback can be initiated at an address other than
frame 0 via the new microprocessor interface (MPI)
control registers (see the Microprocessor Interface
(MPI) section for more information). In all cases, read-
back is performed at sequential addresses from the
start address.
It should be noted that the RD_DATA output pin is also
used as the dedicated boundary-scan output pin, TDO.
If this pin is being used as TDO, the RD_DATA output
from readback can be routed internally to any other pin
desired. The RD_CFG input pin is also used to control
the global 3-state (TS_ALL) function. Before and dur-
ing configuration, the TS_ALL signal is always driven
by the RD_CFG input and readback is disabled. After
configuration, the selection as to whether this input
drives the readback or global 3-state function is deter-
mined by a set of bit stream options. If used as the
RD_CFG
input for readback, the internal TS_ALL input
can be routed internally to be driven by any input pin.
Table 12. Readback Options
Option
Function
0
Prohibit Readback
1
Allow One Readback Only
U
Allow Unrestricted Number of Readbacks
相關PDF資料 |
PDF描述 |
|---|---|
| OR3T125-4PS208 | FPGA, 784 CLBS, 92000 GATES, 80 MHz, PQFP208 |
| OR3T55-4PS208I | FPGA, 324 CLBS, 40000 GATES, 80 MHz, PQFP208 |
| OR3T55-4PS208 | FPGA, 324 CLBS, 40000 GATES, 80 MHz, PQFP208 |
| OR3T80-4PS208I | FPGA, 484 CLBS, 58000 GATES, 80 MHz, PQFP208 |
| OR3T80-4PS208 | FPGA, 484 CLBS, 58000 GATES, 80 MHz, PQFP208 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OR3T125-4PS240I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field Programmable Gate Array (FPGA) |
| OR3T125-5BA352 | 制造商:AGERE 制造商全稱:AGERE 功能描述:3C and 3T Field-Programmable Gate Arrays |
| OR3T125-5BA352I | 制造商:AGERE 制造商全稱:AGERE 功能描述:3C and 3T Field-Programmable Gate Arrays |
| OR3T125-5BC432 | 制造商:AGERE 制造商全稱:AGERE 功能描述:3C and 3T Field-Programmable Gate Arrays |
| OR3T125-5BC432I | 制造商:AGERE 制造商全稱:AGERE 功能描述:3C and 3T Field-Programmable Gate Arrays |
發布緊急采購，3分鐘左右您將得到回復。