- 您現在的位置：買賣IC網 > PDF目錄17162 > OM11078 (NXP Semiconductors)KIT LCD TOUCH 5.7" FOR LPC3250 PDF資料下載
參數資料
| 型號： | OM11078 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 12/57頁 |
| 文件大?。?/td> | 0K |
| 描述： | KIT LCD TOUCH 5.7" FOR LPC3250 |
| 標準包裝： | 1 |
| 傳感器類型： | 觸摸屏幕 |
| 電源電壓： | 5V |
| 嵌入式： | 是，MCU，16/32 位 |
| 已供物品： | 主板，LPC3250 板，LCD 觸摸屏板，線纜，CD，調試器，電源 |
| 已用 IC / 零件： | LPC3250 ARM9 |
| 配用： | 568-4744-ND - MODULE DIMM LPC3250 ARM9 568-4742-ND - MODULE DIMM LPC2478 ARM7 |
| 相關產品： | 568-4533-ND - IC ARM9 MCU 256K 296-TFBGA |
| 其它名稱： | 568-4743 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
LPC3220_30_40_50
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 2 — 20 October 2011
2 of 79
NXP Semiconductors
LPC3220/30/40/50
16/32-bit ARM microcontrollers
External memory controller for DDR and SDR SDRAM as well as for static devices.
Two NAND flash controllers: One for single-level NAND flash devices and the other for
multi-level NAND flash devices.
Master Interrupt Controller (MIC) and two Slave Interrupt Controllers (SIC), supporting
74 interrupt sources.
Eight channel General Purpose DMA (GPDMA) controller on the AHB that can be
used with the SD card port, the high-speed UARTs, I2S-bus interfaces, and SPI
interfaces, as well as memory-to-memory transfers.
Serial interfaces:
10/100 Ethernet MAC with dedicated DMA Controller.
USB interface supporting either device, host (OHCI compliant), or On-The-Go
(OTG) with an integral DMA controller and dedicated PLL to generate the required
48 MHz USB clock.
Four standard UARTs with fractional baud rate generation and 64 byte FIFOs. One
of the standard UARTs supports IrDA.
Three additional high-speed UARTs intended for on-board communications that
support baud rates up to 921 600 when using a 13 MHz main oscillator. All
high-speed UARTs provide 64 byte FIFOs.
Two SPI controllers.
Two SSP controllers.
Two I2C-bus interfaces with standard open-drain pins. The I2C-bus interfaces
support single master, slave, and multi-master I2C-bus configurations.
Two I2S-bus interfaces, each with separate input and output channels. Each
channel can be operated independently on three pins, or both input and output
channels can be used with only four pins and a shared clock.
Additional peripherals:
LCD controller supporting both STN and TFT panels, with dedicated DMA
controller. Programmable display resolution up to 1024
768.
Secure Digital (SD) memory card interface, which conforms to the SD Memory
Card Specification Version 1.01.
General Purpose (GP) input, output, and I/O pins. Includes 12 GP input pins, 24
GP output pins, and 51 GP I/O pins.
10-bit, 400 kHz Analog-to-Digital Converter (ADC) with input multiplexing from
three pins. Optionally, the ADC can operate as a touch screen controller.
Real-Time Clock (RTC) with separate power pin and dedicated 32 kHz oscillator.
NXP implemented the RTC in an independent on-chip power domain so it can
remain active while the rest of the chip is not powered. The RTC also includes a
32-byte scratch pad memory.
32-bit general purpose high-speed timer with a 16-bit pre-scaler. This timer
includes one external capture input pin and a capture connection to the RTC clock.
Interrupts may be generated using three match registers.
Six enhanced timer/counters which are architecturally identical except for the
peripheral base address. Two capture inputs and two match outputs are pinned out
to four timers. Timer 1 brings out a third match output, timers 2 and 3 bring out all
four match outputs, timer 4 has one match output, and timer 5 has no inputs or
outputs.
32-bit millisecond timer driven from the RTC clock. This timer can generate
interrupts using two match registers.
相關PDF資料 |
PDF描述 |
|---|---|
| 24180C | INDUCTOR 18UH 1.26A SMD |
| LTC1558CS-5#TRPBF | IC BACKUP BATT CNTRLR 5V 16-SOIC |
| DK-57TS-LPC3250 | KIT LCD TOUCH 5.7" FOR LPC3250 |
| 594D107X9016C2W | CAP TANT 100UF 16V 10% 2812 |
| C8051F020DK | DEV KIT FOR F020/F021/F022/F023 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OM11078,598 | 功能描述:開發板和工具包 - ARM NXP LPC3250 IRD2.0-5.7"LCD/Lnx RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V |
| OM11079 | 功能描述:MODULE DIMM LPC3250 ARM9 RoHS:是 類別:編程器，開發系統 >> 配件 系列:- 標準包裝:1 系列:- 附件類型:適配器板 適用于相關產品:RCB230，RCB231，RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE |
| OM11079,598 | 功能描述:開發板和工具包 - ARM NXP LPC3250 SODIMM for IRD2.0 RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V |
| OM11080,598 | 制造商:NXP Semiconductors 功能描述:LPC1768 CORTEX-M3 3.2" 2X40 LCD DISPLAY KIT, ARM CORTEX-M3 M - Boxed Product (Development Kits) |
| OM11082,598 | 功能描述:開發板和工具包 - ARM NXP LPC3250 IRD2.0-5.7"LCD/Lnx RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。