- 您現在的位置：買賣IC網 > Datasheet目錄45 > NCP1927DR2G (ON Semiconductor)IC CTLR PFC/FLYBACK 16-SOIC Datasheet資料下載
參數資料
| 型號： | NCP1927DR2G |
| 廠商： | ON Semiconductor |
| 文件頁數： | 20/24頁 |
| 文件大?。?/td> | 531K |
| 描述： | IC CTLR PFC/FLYBACK 16-SOIC |
| 標準包裝： | 2,500 |
| 系列： | * |
NCP1927
http://onsemi.com
20
Figure 25. OVP Timing Diagram
PDRV
V
out
V
out(nom)
OVP
time
time
time
Figure 26. POVUV Pin Block
POVUV
R
POVUV1
R
POVUV2
OVP
UVP
V
out
The NCP1927 detects a UVP fault when the output
voltage falls below the UVP limit. During a UVP fault, the
drive output and error amplifier (EA) are disabled, and
C
PControl
is discharged. It is important to note that the PFC
stage does not start if V
POVUV
is lower than V
UVP
. This
protects the application when there is a problem with the
power path to the bulk capacitor (i.e. the capacitor is unable
to charge up) or if the controller is unable to sense the output
voltage (i.e. the POVUV Pin is floating). The output voltage
that causes a UVP fault is calculated using Equation 14.
V
out(UVP)
+ V
UVP
@
R
POVUV1
) R
POVUV2
R
POVUV2
) I
UVP
@ R
POVUV1
(eq. 14)
Overcurrent Protection (OCP)
The NCP1927 contains an OCP circuit to protect the PFC
stage by limiting the coil current. A current sense resistor
(R
sense
) is inserted in the return path to generate a negative
voltage proportional to the coil current (V
Rsense
) as
portrayed by Figure 27. The circuit uses V
Rsense
to detect
when the coil current exceeds its maximum permissible
level. To do so, the circuit incorporates an operational
amplifier that sources the current necessary to maintain the
PCS pin at zero volts. A resistor (R
PCS
) inserted between the
PCS pin and R
sense
allows the current sourced by the PCS
pin (I
PCS
) to be adjusted via Equation 15.
R
sense
@ I
L
)
R
PCS
@ I
PCS
+ 0
(eq. 15)
where I
L
is the current flowing through the boost inductor.
Rearranging Equation 15 allows I
PCS
to be calculated
using Equation 16.
I
PCS
+
R
sense
R
PCS
@ I
L
(eq. 16)
If I
PCS
exceeds I
OCP
(typically 250 mA), an OCP
condition is detected and the driver is turned off. The driver
remains off until I
PCS
falls below I
OCP
, and the next ZCD
transition occurs or the watchdog timer expires. The
maximum coil current (I
L(MAX)
) is calculated with
Equation 17.
I
L(MAX)
+
R
PCS
R
sense
@ I
OCP
(eq. 17)
where I
OCP
is the OCP threshold current.
Figure 27. Current Sense Block
+
To PDRV disable
PCS
I
PCS
> I
OCP
V
DD
R
PCS
I
PCS
R
sense
I
PCS
I
L
相關PDF資料 |
PDF描述 |
|---|---|
| NCP380HMU21AATBG | IC CURRENT LIMIT SWITCH 6-UDFN |
| NCT1008DMT3R2G | TMP DIO MON/SMBUS 4CH 8WDFN |
| NCT210RQR2G | IC TEMP SENSOR LOC/REM 16QSOP |
| NCT214MT3R2G | IC TEMP SENSOR LOC/REM 10WDFN |
| NCT72CMNR2G | IC REMOTE THERMAL SENSOR 8-DFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1937A1DR2G | 制造商:ON Semiconductor 功能描述:COMBO PFC & QUAZI FLYBACK - Tape and Reel 制造商:ON Semiconductor 功能描述:REEL / COMBO PFC & QUAZI FLYBACK |
| NCP1937B1DR2G | 制造商:ON Semiconductor 功能描述:COMBO PFC & QUAZI FLYBACK - Tape and Reel |
| NCP1937BADAPGEVB | 制造商:ON Semiconductor 功能描述:ADPTR 90W PFC+QR<10MW - Bulk 制造商:ON Semiconductor 功能描述:BOARD EVAL FOR NCP1937 制造商:ON Semiconductor 功能描述:Power Management IC Development Tools 90 W Adapter PFC+QR 10 MW Eval Brd |
| NCP21WB333 | 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:for Surface Mounting Application |
| NCP21WB333J03RA | 功能描述:熱敏電阻 - NTC 33K OHM 5% RoHS:否 制造商:EPCOS 電阻:10 kOhms 功率額定值:150 mW 容差:2 % 端接類型:Radial 系列:B57703M 工作溫度范圍:- 55 C to + 125 C |
發布緊急采購，3分鐘左右您將得到回復。