- 您現在的位置：買賣IC網 > PDF目錄361092 > NCP1523 (Texas Instruments, Inc.) 6-A, 2.2-V to 5.5-V INPUT, NON-ISOLATED, WIDE-OUTPUT, ADJUSTABLE POWER MODULE WITH TurboTrans PDF資料下載
參數資料
| 型號： | NCP1523 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 6-A, 2.2-V to 5.5-V INPUT, NON-ISOLATED, WIDE-OUTPUT, ADJUSTABLE POWER MODULE WITH TurboTrans |
| 中文描述： | 6甲，2.2 V至5.5 V輸入，非隔離，寬輸出，可調電源模塊的TurboTrans |
| 文件頁數： | 27/35頁 |
| 文件大小： | 1128K |
| 代理商： | NCP1523 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
www.ti.com
Notes on Use of Auto-Track
1. The
Track
pin voltage must be allowed to rise above the module set-point voltage before the module
regulates at its adjusted set-point voltage.
2. The Auto-Track function tracks almost any voltage ramp during power up, and is compatible with ramp
speeds of up to 1 V/ms.
3. The absolute maximum voltage that may be applied to the
Track
pin is the input voltage V
I
.
4. The module cannot follow a voltage at its track control input until it has completed its soft-start initialization.
This takes about 20 ms from the time that a valid voltage has been applied to its input. During this period, it
is recommended that the
Track
pin be held at ground potential.
5. The Auto-Track function is disabled by connecting the
Track
pin to the input voltage (V
). When Auto-Track
is disabled, the output voltage rises at a quicker and more linear rate after input power has been applied.
U2
PTH04T230W
Vi
Auto Track
GND
VoAdj
Vo
TurboTrans
+Sense
Sense
Inhibit/
UVLO
U3
TPS3808G50
6
GND
2
4
3
MR
CT
SENSE
5
1
U1
PTH05T210W
Vi
Auto Track
GND
VoAdj
Vo
TurboTrans
+Sense
Sense
+
Inhibit/
UVLO
SmartSync
+
R
TT
V
O1
= 3.3 V
C
O1
V
O2
= 1.8 V
C
O2
R
TT
R
4.75 k
R
SET1
1.62 k
C
I2
C
I1
RESET
V
I
= 5 V
C
0.1
μ
F
C
3
4700
μ
F
UDG06042
PTH04T230W, PTH04T231W
SLTS271A–SEPTEMBER 2006–REVISED OCTOBER 2006
Figure 24. Sequenced Power Up and Power Down Using Auto-Track
27
Submit Documentation Feedback
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1560 | Full Featured Voltage Mode PWM Controller(全性能電壓模式PWM控制器) |
| NCP1560HDR2 | Quadruple Differential Line Receiver With 3-State Outputs 16-PDIP 0 to 70 |
| NCP1562A | High Performance Active Active Clamp/Reset PWM Controller Controller(高性能有效Clamp/Reset PWM控制器) |
| NCP1562B | High Performance Active Active Clamp/Reset PWM Controller Controller(高性能有效Active Clamp/Reset PWM控制器) |
| NCP1729 | Switched Capacitor Voltage Inverter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1523BFCT2G | 功能描述:直流/直流開關轉換器 FORCED PWM NCP1523 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCP1523BGEVB | 功能描述:電源管理IC開發工具 NCP1523B EVAL BRD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| NCP1523FCT2G | 功能描述:直流/直流開關轉換器 UBUMP DCDC RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCP1526EVB | 功能描述:電源管理IC開發工具 NCP1526 EVALUATION BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| NCP1526MUTXG | 功能描述:直流/直流開關轉換器 BUCK REG AND LDO RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。