參數資料
型號： NCP1523
廠商： Texas Instruments, Inc.
英文描述： 6-A, 2.2-V to 5.5-V INPUT, NON-ISOLATED, WIDE-OUTPUT, ADJUSTABLE POWER MODULE WITH TurboTrans
中文描述： 6甲，2.2 V至5.5 V輸入，非隔離，寬輸出，可調電源模塊的TurboTrans
文件頁數： 25/35頁
文件大?。?/td> 1128K
代理商： NCP1523
www.ti.com
Overtemperature Protection (OTP)
A thermal shutdown mechanism protects the module’s internal circuitry against excessively high temperatures. A
rise in the internal temperature may be the result of a drop in airflow, or a high ambient temperature. If the
internal temperature exceeds the OTP threshold, the module’s Inhibit control is internally pulled low. This turns
the output off. The output voltage drops as the external output capacitors are discharged by the load circuit. The
recovery is automatic, and begins with a soft-start power up. It occurs when the sensed temperature decreases
by about 10
°
C below the trip point.
The overtemperature protection is a last resort mechanism to prevent thermal stress to the regulator.
Operation at or close to the thermal shutdown temperature is not recommended and reduces the long-term
reliability of the module. Always operate the regulator within the specified safe operating area (SOA) limits
for the worst-case conditions of ambient temperature and airflow.
Smart Sync
Smart Sync is a feature that allows multiple power modules to be synchronized to a common frequency. Driving
the Smart Sync pins with an external oscillator set to the desired frequency, synchronizes all connected modules
to the selected frequency. The synchronization frequency can be higher or lower than the nominal switching
frequency of the modules within the range of 240 kHz to 400 kHz (see Electrical Specifications table for
frequency limits). Synchronizing modules powered from the same bus eliminates beat frequencies reflected back
to the input supply, and also reduces EMI filtering requirements. These are the benefits of Smart Sync. Power
modules can also be synchronized out of phase to minimize source current loading and minimize input
capacitance requirements.
Figure 23
shows a standard circuit with two modules syncronized 180
°
out of phase
using a D flip-flop.
PTH04T240W
Vi
Track
GND
VoAdj
Vo
TT
+Sense
Sense
Inhibit/
UVLO
GND
D
PRE
PTH04T230W
Vi
GND
VoAdj
Vo
TT
+Sense
Sense
+
Inhibit/
UVLO
Sync
+
+
Q
CLK
SN74LVC2G74
+
SYNC
R
SET1
f
CLK
= 2 x f
MODULE
V
O1
0
°
180
°
V
CC
CLR
Q
V
O2
C
O1
C
O2
UDG06054
C
I1
C
I2
R
SET2
Track
V
I
=5 V
PTH04T230W, PTH04T231W
SLTS271A–SEPTEMBER 2006–REVISED OCTOBER 2006
Figure 23. Typical SmartSync Circuit
25
Submit Documentation Feedback
相關PDF資料
PDF描述
NCP1560 Full Featured Voltage Mode PWM Controller(全性能電壓模式PWM控制器)
NCP1560HDR2 Quadruple Differential Line Receiver With 3-State Outputs 16-PDIP 0 to 70
NCP1562A High Performance Active Active Clamp/Reset PWM Controller Controller(高性能有效Clamp/Reset PWM控制器)
NCP1562B High Performance Active Active Clamp/Reset PWM Controller Controller(高性能有效Active Clamp/Reset PWM控制器)
NCP1729 Switched Capacitor Voltage Inverter
相關代理商/技術參數
參數描述
NCP1523BFCT2G 功能描述:直流/直流開關轉換器 FORCED PWM NCP1523 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
NCP1523BGEVB 功能描述:電源管理IC開發工具 NCP1523B EVAL BRD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
NCP1523FCT2G 功能描述:直流/直流開關轉換器 UBUMP DCDC RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
NCP1526EVB 功能描述:電源管理IC開發工具 NCP1526 EVALUATION BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
NCP1526MUTXG 功能描述:直流/直流開關轉換器 BUCK REG AND LDO RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*