- 您現在的位置：買賣IC網 > PDF目錄361092 > NCP1523 (Texas Instruments, Inc.) 6-A, 2.2-V to 5.5-V INPUT, NON-ISOLATED, WIDE-OUTPUT, ADJUSTABLE POWER MODULE WITH TurboTrans PDF資料下載
參數資料
| 型號： | NCP1523 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 6-A, 2.2-V to 5.5-V INPUT, NON-ISOLATED, WIDE-OUTPUT, ADJUSTABLE POWER MODULE WITH TurboTrans |
| 中文描述： | 6甲，2.2 V至5.5 V輸入，非隔離，寬輸出，可調電源模塊的TurboTrans |
| 文件頁數： | 23/35頁 |
| 文件大?。?/td> | 1128K |
| 代理商： | NCP1523 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
www.ti.com
Soft-Start Power Up
The Auto-Track feature allows the power-up of multiple PTH/PTV modules to be directly controlled from the
Track pin. However in a stand-alone configuration, or when the Auto-Track feature is not being used, the Track
pin should be directly connected to the input voltage, V
I
(see
Figure 19
).
UDG06044
V
I
V
I
Track
GND
2
9
3
+
GND
C
I
PTH04T230/231W
V
I
(2 V/div)
V
(1 V/div)
I
I
(2 A/div)
T Time 4 ms/div
Remote Sense
Differential remote sense improves the load regulation performance of the module by allowing it to compensate
for any IR voltage drop between its output and the load in either the positive or return path. An IR drop is caused
by the output current flowing through the small amount of pin and trace resistance. Connecting the +Sense (pin
5) and –Sense (pin 6) pins to the respective positive and ground reference of the load terminals improves the
load regulation of the output voltage at the connection points.
PTH04T230W, PTH04T231W
SLTS271A–SEPTEMBER 2006–REVISED OCTOBER 2006
Figure 19. Defeating the Auto-Track Function
Figure 20. Power-Up Waveform
When the Track pin is connected to the input voltage the Auto-Track function is permanently disengaged. This
allows the module to power up entirely under the control of its internal soft-start circuitry. When power up is
under soft-start control, the output voltage rises to the set-point at a quicker and more linear rate. From the
moment a valid input voltage is applied, the soft-start control introduces a short time delay (typically
2 ms–10 ms) before allowing the output voltage to rise. The output then progressively rises to the module’s
setpoint voltage.
Figure 20
shows the soft-start power-up characteristic of the PTH04T230/231W operating from a 5-V input bus
and configured for a 1.8-V output. The waveforms were measured with a 6-A constant current load and the
Auto-Track feature disabled. The initial rise in input current when the input voltage first starts to rise is the
charge current drawn by the input capacitors. Power-up is complete within 20 ms.
With the sense pins connected at the load, the difference between the voltage measured directly between the
V
and GND pins, and that measured at the Sense pins, is the amount of IR drop being compensated by the
regulator. This should be limited to a maximum of 300 mV.
If the remote sense feature is not used at the load, connect the +Sense pin to V
O
(pin 4) and connect the
–Sense pin to the module GND (pin 3).
The remote sense feature is not designed to compensate for the forward drop of nonlinear or frequency
dependent components that may be placed in series with the converter output. Examples include OR-ing
diodes, filter inductors, ferrite beads, and fuses. When these components are enclosed by the remote sense
connection they are effectively placed inside the regulation control loop, which can adversely affect the
stability of the regulator.
23
Submit Documentation Feedback
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1560 | Full Featured Voltage Mode PWM Controller(全性能電壓模式PWM控制器) |
| NCP1560HDR2 | Quadruple Differential Line Receiver With 3-State Outputs 16-PDIP 0 to 70 |
| NCP1562A | High Performance Active Active Clamp/Reset PWM Controller Controller(高性能有效Clamp/Reset PWM控制器) |
| NCP1562B | High Performance Active Active Clamp/Reset PWM Controller Controller(高性能有效Active Clamp/Reset PWM控制器) |
| NCP1729 | Switched Capacitor Voltage Inverter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1523BFCT2G | 功能描述:直流/直流開關轉換器 FORCED PWM NCP1523 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCP1523BGEVB | 功能描述:電源管理IC開發工具 NCP1523B EVAL BRD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| NCP1523FCT2G | 功能描述:直流/直流開關轉換器 UBUMP DCDC RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCP1526EVB | 功能描述:電源管理IC開發工具 NCP1526 EVALUATION BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| NCP1526MUTXG | 功能描述:直流/直流開關轉換器 BUCK REG AND LDO RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。