- 您現在的位置：買賣IC網 > PDF目錄1956 > NCN6000DTBR2G (ON Semiconductor)IC INTERFACE SMART CARD 20TSSOP PDF資料下載
參數資料
| 型號： | NCN6000DTBR2G |
| 廠商： | ON Semiconductor |
| 文件頁數： | 11/36頁 |
| 文件大小： | 0K |
| 描述： | IC INTERFACE SMART CARD 20TSSOP |
| 產品變化通告： | Product Obsolescence 01/Jul/2009 |
| 標準包裝： | 1 |
| 應用： | ATM 終端，氣泵，ISM |
| 接口： | 微控制器 |
| 電源電壓： | 2.7 V ~ 6 V |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 剪切帶 (CT) |
| 安裝類型： | 表面貼裝 |
| 其它名稱： | NCN6000DTBR2GOSCT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
NCN6000
http://onsemi.com
19
Card Detection
The card detector circuit provides a 500 k
W pull up
resistor to bias the CRD_DET pin, yielding a logic High
when the pin is left open (assuming a NO switch). The
internal logic associated with pin 11 provides an automatic
selection of the slope card detection, depending upon the
polarity set by the external MPU. At start up, the CRD_DET
is preset to cope with Normally Open switch. When a
Normally Close switch is used in the card socket, it is
mandatory to program the NCN6000 chip during the
initialization sequence, otherwise the system will not start if
a card was previously inserted. Table 3 gives the
programming code for such a function. The next lines
provide a typical assembler source to handle this CRD_DET
Normally Close polarity:
Smart EQU $20
LDX
#$1000
LDAA #$09
STAA smart, X
; NCN6000 Physical CS Address
; Offset
; I/O = H, A0 = A1 = L, RESET = H
; Set CRD_DET = Normally Closed
Switch
The CRD_DET polarity can be updated at any time,
during the Program Mode sequence (PGM = L), but,
generally speaking, is useless since the switch does not
change during the usage of the considered module. On the
other hand, the card detection switch shall be connected
across pin 11 and ground, for any polarity selected.
The transition presents pin 11, whatever be the polarity, is
filtered out by the internal digital filter circuit, avoiding false
interrupt. In addition to the minimum internal 50
ms timing,
the MPU shall provide an additional delay to cope with the
mechanical stabilization of the card interface (typically
3 ms), prior to valid the CRD_VCC supply.
When a card is inserted, the detector circuit asserts
INT = Low as depicted before. When the NCN6000 detects
a card extraction, the power down sequence is activated,
regardless of the PWR_ON state, and the INT pin is asserted
Low. It is up to the external MPU to clear this interrupt by
forcing a chip select pulse as depicted in Figure 5.
The 75
ms delay represent the digital filter builtin the
NCN6000 chip being used for the characterization. Any
pulse shorter than this delay does not generate an interrupt.
However, to guarantee an interrupt will be generated, the
CRD_DET signal must be longer than 150
ms as defined by
the specification.
The Chip Select pulse is generated by the external
microcontroller, the minimum pulse width being 2
ms to
make sure the card is detected.
The oscillogram, Figure 11, depicts the behavior for a
Normally Open switch, the delay existing between the
interrupt negative going state and the CS being Low comes
from the particular software latency existing in this
particular MPU.
Figure 11. Card Insertion Detection and Interrupt Signals
Digital Filter Delay
INTERRUPT
Chip Select Acknowledge or Clear Interrupt
相關PDF資料 |
PDF描述 |
|---|---|
| NCN6001DTBR2 | IC INTERFACE SMART CARD 20TSSOP |
| NCN6004AFTBR2G | IC INTERFACE SAM/SIM DUAL 48TQFP |
| NCN6804MNR2G | IC SMART CARD DUAL W/SPI 32-QFN |
| NCN7200MTTWG | IC MUX/DEMUX OCTAL 1X2 42WQFN |
| NCN8024DTBR2G | SMART CARD IC 5V/3V TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCN6001 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Smartcard Interface ICs |
| NCN6001/D | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Compact Smart Card Interface IC |
| NCN6001_06 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Compact Smart Card Interface IC |
| NCN6001_0610 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Smartcard Interface ICs |
| NCN6001DTBEVB | 功能描述:界面開發工具 NCN6001 TSSOP EVAL BOARD RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。