參數資料
型號: MT90863
廠商: Mitel Networks Corporation
英文描述: 3V Rate Conversion Digital Switch(3V 速率轉換數字開關)
中文描述: 3V的速率轉換數字交換機(3V的速率轉換數字開關)
文件頁數: 15/35頁
文件大小: 168K
代理商: MT90863
Advance Information
MT90863
15
Table 8 - Internal Mode Selection (IMS) Register Bits
Bit
Name
Description
15-10
Unused
Must be zero for normal operation.
9-7
BBPD2-0
Backplane Block Programming Data.
These bits carry the value to be loaded into
the backplane connection memory block when the Memory Block Programming
feature is active. After the MBP bit in the control register is set to 1 and the BPE bit is
set to 1, the contents of bits BBPD2-0 are loaded into the bit 13 to bit 11 position of
the backplane connection memory. Bit 15, bit 14 and bit 10 to bit 0 of the backplane
connection memory are zeroed.
6-3
LBPD3-0
Local Block Programming Data.
These bits carry the value to be loaded into the
local connection memory block when the Memory Block Programming feature is
active. After the MBP bit in the control register is set to 1 and the BPE bit is set to 1,
the contents of bits LBPD3-0 are loaded into the bit 15 to bit 12 position of the local
connection memory. Bit 11 to bit 0 of the local connection memory low are zeroed. Bit
15 to bit 0 of local connection memory high are zeroed.
2
BPE
Begin Block Programming Enable.
A zero to one transition of this bit enables the
memory block programming function. The BPE, BBPD2-0 and LBPD3-0 bits in the
IMS register must be defined in the same write operation. Once the BPE bit is set
high, the device requires two frames to complete the block programming. After the
programming function has finished, the BPE bit returns to zero to indicate the
operation is completed. When the BPE = 1, the BPE or MBP can be set to 0 to abort
the programming operation.
When BPE = 1, the other bits in the IMS register must not be changed for two frames
to ensure proper operation.
1
OSB
Output Stand By.
This bit controls the device output drivers.
OSB bit ODE pin OE bit
0 0 1 High impedance state
1 0 1 Enable
X 1 1 Enable
X X 0 Per-channel high impedance
STio0 - 31, STo0 - 15
0
SFE
Start Frame Evaluation.
A zero to one transition in this bit starts the frame evaluation
procedure. When the CFE bit in the FAR register changes from zero to one, the
evaluation procedure stops. Set this bit to zero for at least one frame (125
μ
s) to start
another frame evaluation.
Read/Write Address:
Reset Value:
02
H
,
0000
H
.
7
6
5
4
3
2
1
0
8
9
10
11
12
13
LBPD
3
BBPD
0
BBPD
1
0
14
15
LBPD
2
0
BBPD
2
BPE
OSB
SFE
1
0
0
0
0
0
LBPD
LBPD
相關PDF資料
PDF描述
MT9125 Dual ADPCM Transcoder(雙ADPCM編解碼器)
MT91600 Programmable SLIC(可編程用戶線路接口電路(在轉換系統和用戶環間提供一個接口))
MT9162 5 Volt Single Rail Codec(5V 單軌編解碼器)
MT9174 ISO2-CMOS ST-BUS⑩ FAMILY Digital Network Interface Circuit with Receive Sync Marker Bit
MT9174AE ISO2-CMOS ST-BUS⑩ FAMILY Digital Network Interface Circuit with Receive Sync Marker Bit
相關代理商/技術參數
參數描述
MT90863AG 制造商:Microsemi Corporation 功能描述:RATE CONVERSION DIGITAL SWITCH - Trays 制造商:Microsemi Corporation 功能描述:Microsemi MT90863AG Communication Misc 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC DGTL SWITCH RCDX 144PBGA 制造商:Microsemi Corporation 功能描述:IC DGTL SWITCH RCDX 144PBGA
MT90863AG1 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:3V Rate Conversion Digital Switch
MT90863AG2 制造商:Microsemi Corporation 功能描述:SWITES 144BGA - Trays 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC DGTL SWITCH RCDX 144PBGA 制造商:Microsemi Corporation 功能描述:IC DGTL SWITCH RCDX 144PBGA
MT90863AL 制造商:Microsemi Corporation 功能描述:RATE CONVERSION DIGITAL SWITCH - Trays
MT90863AL1 制造商:Microsemi Corporation 功能描述:PB FREE RATE CONVERSION DIGITAL SWITCH - Trays 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC DGTL SWITCH RCDX 128MQFP