參數資料
型號： MT9076AB
廠商： Mitel Networks Corporation
英文描述： T1/E1/J1 3.3V Single Chip Transceiver
中文描述： T1/E1/J1收發3.3V的單芯片收發器
文件頁數： 120/160頁
文件大小： 416K
代理商： MT9076AB
MT9076
Preliminary Information
116
Bit
Name
Functional Description
7
RAIS
Remote Alarm Indication Status
. If one, there is currently a remote alarm condition (i.e.,
received A bit is one). If zero, normal operation. Updated on a non-frame alignment frame
basis.
6
AISS
Alarm Indication Status Signal
. If one, indicates that a valid AIS or all ones signal is
being received. If zero, indicates that a valid AIS signal is not being received. The criteria
for AIS detection is determined by the control bit ASEL.
5
AIS16S
Alarm Indication Signal 16 Status
. If one, indicates an all ones alarm is being received in
channel 16. If zero, normal operation. Updated on a frame basis.
4
LOSS
Loss of Signal Status
. If one, indicates the presence of a loss of signal condition. If zero,
indicates normal operation. A loss of signal condition occurs when an excess consecutive
bit periods are zero. The threshold for this condition is set by the control bit L32Z. If L32Z is
set high the threshold is 32 successive zeros. If L32Z is set low the threshold is 192
successive zeros. A loss of signal condition terminates when an average ones density of at
least 12.5% has been received over a period of 192 contiguous pulse positions starting
with a pulse.
3
AUXPS
Auxiliary Pattern Status
. This bit goes on high when a continuous 101010... bit stream
(Auxiliary Pattern) is received on the PCM 30 link for a period of at least 512 bits. If zero,
auxiliary pattern is not being received. This pattern will be decoded in the presence of a bit
error rate of as much as 10-3.
2
MFALMS
Multiframe Alarm Status
. This bit goes high in the event of receipt of a multiframe alarm.
It goes low when the received multiframe alarm bit goes low.
1
RSLIPS
Receive Slip Status
. A change of state (i.e., 1-to-0 or 0-to-1) indicates that a receive
controlled frame slip has occurred.
0
- - -
Unused
.
Table 129 - Alarm Status Word 2
(Page 3, Address 1BH) (E1)
Bit
Name
Functional Description
7 - 0
AP4-0
Analog Peak Detector
. This status register gives the output value of a 5 bit A/D converter
connected to a peak detector on RTIP/RRING.
Table 130 - Analog Peak Detector
(Page 3, Address 1DH) (E1)
Bit
Name
Functional Description
7 - 0
ESP7-0
Analog Peak
. This status register gives the output value of an 8 bit A/D
converter connected to a peak detector on RTIP/RRING.
Table 131 - Equalized Signal Peak Detect
(Page 3, Address 1EH) (E1)
Bit
Name
Functional Description
7-0
ID7-0
ID Number.
Contains device code 01111000
Table 132 - Identification Word
(Page 3, Address 1FH) (E1)
相關PDF資料
PDF描述
MT9076 T1/E1/J1 3.3V Single Chip Transceiver(T1/E1/J1 3.3V 單片收發器)
MT9079 Advanced Controller for E1(先進的E1幀調節器和控制器)
MT9080B SMX - Switch Matrix Module(用于消費類轉換應用的開關矩陣模塊)
MT90810 Flexible MVIP(Multi-Vendor Integration Protocol) Interface Circuit(彈性MVIP接口電路)
MT90812 Integrated Digital Switch (IDX)(集成數字開關)
相關代理商/技術參數
參數描述
MT9076AP 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1/E1/J1 3.3V Single Chip Transceiver
MT9076B 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1/J1 3.3 V Single Chip Transceiver
MT9076BB 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 80LQFP - Trays
MT9076BB1 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 80LQFP - Trays
MT9076BP 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1/J1 3.3 V Single Chip Transceiver
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*