參數資料
型號： MT9075B
廠商： Mitel Networks Corporation
英文描述： E1 Single Chip Transceiver(E1單片收發器)
中文描述： 素E1單芯片收發器（素E1單片收發器）
文件頁數： 8/82頁
文件大?。?/td> 275K
代理商： MT9075B
MT9075B
Preliminary Information
8
Functional Description
MT9075B Line Interface Unit (LIU)
Receiver
The receiver portion of the MT9075B LIU consists of
an input signal peak detector, an optional two-stage
equalizer, a smoothing filter, adaptive threshold
comparators, data and clock slicers, and a clock
extractor. Receive equalization gain can be set via
software
control
or
it
automatically by the peak detectors.
can
be
determined
The output of the receive equalizer is conditioned by
a smoothing filter and is passed on to the clock and
data slicer. The clock slicer output signal drives a
phase locked loop, which generates the extracted
clock (E2o). This extracted clock is used to sample
the output of the data comparator.
The LOS output pin (pin 61 in PLCC, pin 57 in
MQFP) is user selectable, by setting control bit LOS/
LOF (page 02H, register 13H, bit 2), to indicate a
loss of signal or loss of basic frame synchronization
condition. In addition, a status bit, LLOS (bit 4 in
page 3, register 18H) is provided to indicate the
presence of a loss signal condition. The occurrence
of a loss signal condition is defined as per I.431, i.e.,
when the incoming signal amplitude is more than 20
dB below the nominal amplitude for a time duration
of at least 1 ms.
The receive LIU circuit requires a terminating
resistor of either 120
or 75
across the device side
of the receive1:1 transformer as shown in Figure 4.
The return loss of the receiver, complying with
G.703, is greater than:
12 dB from 51 kHz to 102 kHz;
18 dB from 102 kHz to 2048 kHz;
14 dB from 2048 kHz to 3072 kHz.
The jitter tolerance of the MT9075B clock extractor
circuit exceeds the requirements of G.823 (Figure 3).
Transmitter
The MT9075B differential line driver is designed to
drive a 1:2 step-up transformer (see Figure 4). A
0.68 uF capacitor is required between the TTIP and
the transmit transformer. Resistors R
T
(as shown in
Figure 4) are for termination for transmit return loss.
The values of R
T
may be optimized for 120
lines,
75
lines or set at an intermediary value to serve
both applications. Program the Transmit Pulse
Control Word (address 1FH page 1) to adjust the
pulse amplitude accordingly. Alternatively, the pulse
level and shape may be discretely programmed by
writing to the Customer Pulse Level registers
(addresses 1CH to 1FH, page 2) and setting the
Custom Transmit Pulse bit high (bit 3 of the Transmit
Pulse Control Word).
Figure 3 - Typical Jitter Tolerance
18UI
1.5UI
0.2UI
1.667Hz
20Hz
2.4kHz 18kHz 100kHz
Peak to Peak
Jitter Amplitude
(log scale)
Jitter Frequency
(log scale)
MT9075B
Tolerance
相關PDF資料
PDF描述
MT9075 E1 Single Chip Transceiver
MT9075A E1 Single Chip Transceiver
MT9075AL E1 Single Chip Transceiver
MT9075AP E1 Single Chip Transceiver
MT9075BL E1 Single Chip Transceiver
相關代理商/技術參數
參數描述
MT9075B-1 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:E1 Single Chip Transceiver
MT9075BL 制造商:Microsemi Corporation 功能描述:FRAMER E1 5V 100MQFP - Trays
MT9075BL1 制造商:Microsemi Corporation 功能描述:FRAMER E1 5V 100MQFP - Trays 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TXRX SGL E1 W/LIU 100MQFP 制造商:Microsemi Corporation 功能描述:IC TXRX SGL E1 W/LIU 100MQFP
MT9075BP 制造商:Microsemi Corporation 功能描述:
MT9075BP1 制造商:Microsemi Corporation 功能描述:Single Chip Transceiver 1TX 1RX 2.048Mbps 68-Pin PLCC Tube 制造商:Microsemi Corporation 功能描述:FRAMER E1 5V 68PLCC - Rail/Tube 制造商:Microsemi Corporation 功能描述:PB FREE E1 SINGLE CHIP TRANSCEIVER 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TXRX SGL E1 W/LIU 68PLCC 制造商:Microsemi Corporation 功能描述:IC TXRX SGL E1 W/LIU 68PLCC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*