參數資料
型號: MT9075B
廠商: Mitel Networks Corporation
英文描述: E1 Single Chip Transceiver(E1單片收發器)
中文描述: 素E1單芯片收發器(素E1單片收發器)
文件頁數: 39/82頁
文件大?。?/td> 275K
代理商: MT9075B
Preliminary Information
MT9075B
39
Bit
Name
Functional Description
7
BPVE
(0)
Bipolar Violation Error Insertion.
A zero-to-one transition of this bit
inserts a single bipolar violation
error into the transmit PCM 30 data.
A one, zero or one-to-zero transition
has no function.
6
CRCE
(0)
CRC-4 Error Insertion.
A zero-to-
one transition of this bit inserts a
single CRC-4 error into the transmit
PCM 30 data. A one, zero or one-to-
zero transition has no function.
5
FASE
(0)
Frame Alignment Signal Error
Insertion.
A zero-to-one transition
of this bit inserts a single error into
the time slot zero frame alignment
signal of the transmit PCM 30 data.
A one, zero or one-to-zero transition
has no function.
4
NFSE
(0)
Non-frame
Error Insertion.
A zero-to-one
transition of this bit inserts a single
error into bit two of the time slot zero
non-frame alignment signal of the
transmit PCM 30 data. A one, zero
or one-to-zero transition has no
function.
Alignment
Signal
3
LOSE
(0)
Loss of Signal Error Insertion.
If
one, the MT9075B transmits an all
zeros signal (no pulses) in every
PCM 30 time slot. If zero, data is
transmitted normally.
2
PERR
(0)
Payload Error Insertion.
A zero-to-
one transition of this bit inserts a
single error in the transmit payload.
A one, zero or one-to-zero transition
has no function.
1
---
Unused.
0
DBNCE
(0)
Debounce Select.
This bit selects
the debounce period (1 for 14
msec.; 0 for no debounce). Note:
there may be as much as 2 msec.
added to this duration because the
state change of the signalling
equipment is not synchronous with
the PCM 30 signalling multiframe.
Table 28 - Error and Debounce Selection Word
(Page 02H, Address 10H)
Bit
Name
Functional Description
7-3
--
Unused.
2
LOS/LOF
(0)
Loss of Signal or Loss of Frame
Selection.
If one, pin LOS (pin 61 in
PLCC, 57 in MQFP) will go high
when a loss of signal state exits
(criteria as per LLOS status bit on
page 03H address 18H). If low, pin
LOS will go high when either a loss
of signal (LLOST =1) or a loss of
basic frame alignment state exits
(bit SYNC on page 03H address
10H is zero).
1
ADSEQ
(0)
Digital Milliwatt or Digital Test
Sequence.
If one, the A-law digital
milliwatt analog test sequence will
be selected by the Per Time Slot
Control bits TTST and RTST (on
page 07H and 08H). If zero, the
PRBS 2
15
-1 bit error rate test
sequence will be selected by the
Per Time Slot Control bits TTST and
RTST. The PRBS generator is reset
whenever this bit is set to 1.
0
GCI/ST
(0)
GCI or ST-BUS Frame Pulse.
If
one, the MT9075B will transmit or
receive a GCI frame pulse on pin
F0b (pin 46 in PLCC, 34 in MQFP).
If zero, the MT9075B will transmit or
receive an ST-BUS frame pulse on
F0b.
Table 29 - Access Control Word
(Page 02H, Address 13H)
相關PDF資料
PDF描述
MT9075 E1 Single Chip Transceiver
MT9075A E1 Single Chip Transceiver
MT9075AL E1 Single Chip Transceiver
MT9075AP E1 Single Chip Transceiver
MT9075BL E1 Single Chip Transceiver
相關代理商/技術參數
參數描述
MT9075B-1 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:E1 Single Chip Transceiver
MT9075BL 制造商:Microsemi Corporation 功能描述:FRAMER E1 5V 100MQFP - Trays
MT9075BL1 制造商:Microsemi Corporation 功能描述:FRAMER E1 5V 100MQFP - Trays 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TXRX SGL E1 W/LIU 100MQFP 制造商:Microsemi Corporation 功能描述:IC TXRX SGL E1 W/LIU 100MQFP
MT9075BP 制造商:Microsemi Corporation 功能描述:
MT9075BP1 制造商:Microsemi Corporation 功能描述:Single Chip Transceiver 1TX 1RX 2.048Mbps 68-Pin PLCC Tube 制造商:Microsemi Corporation 功能描述:FRAMER E1 5V 68PLCC - Rail/Tube 制造商:Microsemi Corporation 功能描述:PB FREE E1 SINGLE CHIP TRANSCEIVER 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TXRX SGL E1 W/LIU 68PLCC 制造商:Microsemi Corporation 功能描述:IC TXRX SGL E1 W/LIU 68PLCC