參數資料
型號： MT9044
廠商： Mitel Networks Corporation
英文描述： T1/E1/OC3 System Synchronizer(T1/E1/OC3 系統同步裝置（由一個數字鎖相環組成）)
中文描述： T1/E1/OC3系統同步器（T1/E1/OC3系統同步裝置（由一個數字鎖相環組成））
文件頁數： 8/34頁
文件大?。?/td> 150K
代理商： MT9044
MT9044
8
Input Impairment Monitor
This circuit monitors the input signal to the DPLL and
automatically
enables
(Auto-Holdover) when the frequency of the incoming
signal is outside the auto-holdover capture range
(See AC Electrical Characteristics - Performance).
This includes a complete loss of incoming signal, or
a large frequency shift in the incoming signal. When
the incoming signal returns to normal, the DPLL is
returned to Normal Mode with the output signal
locked to the input signal. The holdover output signal
is based on the incoming signal 30ms minimum to
60ms prior to entering the Holdover Mode. The
amount of phase drift while in holdover is negligible
because the Holdover Mode is very accurate (e.g.
±
0.05ppm). The the Auto-Holdover circuit does not
use TIE correction. Consequently, the phase delay
between the input and output after switching back to
Normal Mode is preserved (is the same as just prior
to the switch to Auto-Holdover).
the
Holdover
Mode
Automatic/Manual Control State Machine
The Automatic/Manual Control State Machine allows
the MT9044 to be controlled automatically (i.e.
LOS1, LOS2 and GTi signals) or controlled manually
(i.e. MS1, MS2, GTi and RSEL signals). With manual
control a single mode of operation (i.e. Normal,
Holdover and Freerun) is selected. Under automatic
control the state of the LOS1, LOS2 and GTi signals
determines the sequence of modes that the MT9044
will follow.
As shown in Figure 1, this state machine controls the
Reference Select MUX, the TIE Corrector Circuit, the
DPLL and the Guard Time Circuit. Control is based
on the logic levels at the control inputs LOS1, LOS2,
RSEL, MS1, MS2 and GTi of the Guard Time Circuit
(See Figure 6).
All state machine changes occur synchronously on
the rising edge of F8o. See the Controls and Modes
of Operation section for full details on Automatic
Control and Manual Control.
Figure 6 - Automatic/Manual Control State
Machine Block Diagram
Guard Time Circuit
The GTi pin is used by the Automatic/Manual Control
State Machine in the MT9044 under either Manual or
Automatic control.
The logic level at the GTi pin
performs two functions, it enables and disables the
TIE Corrector Circuit (Manual and Automatic), and it
selects which mode change takes place (Automatic
only). See the Applications - Guard Time section.
For both Manual and Automatic control, when
switching from Primary Holdover to Primary Normal,
the TIE Corrector Circuit is enabled when GTi=1, and
disabled when GTi=0.
Under Automatic control and in Primary Normal
Mode, two state changes are possible (not counting
Auto-Holdover). These are state changes to Primary
Holdover or to Secondary Normal. The logic level at
the GTi pin determines which state change occurs.
When GTi=0, the state change is to Primary
Holdover.
When GTi=1, the state change is to
Secondary Normal.
Master Clock
The MT9044 can use either a clock or crystal as the
master timing source.
For recommended master
timing circuits, see the Applications - Master Clock
section.
Control and Modes of Operation
The MT9044 can operate either in Manual or
Automatic Control. Each control method has three
possible modes of operation, Normal, Holdover and
Freerun.
As shown in Table 3, Mode/Control Select pins MS2
and MS1 select the mode and method of control.
MS1
MS2
To
Reference
Select MUX
To TIE
Corrector
Enable
Automatic/Manual Control
State Machine
To DPLL
State
Select
RSEL
LOS1
LOS2
To and From
Guard Time
Circuit
Control
RSEL
Input Reference
MANUAL
0
PRI
1
SEC
AUTO
0
State Machine Control
1
Reserved
Table 2 - Input Reference Selection
相關PDF資料
PDF描述
MT90500 Multi-Channel ATM AAL1 SAR(多通道 ATM AAL1分段及重組設備（基于通訊總線的系統與ATM網絡的接口）)
MT90500 Multi-Channel ATM AAL1 SAR
MT90500AL Multi-Channel ATM AAL1 SAR
MT90502 Multi-Channel AAL2 SAR(多通道 ATM AAL2分段及重組設備（基于通訊總線的系統與ATM網絡的接口）)
MT90732AP Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
相關代理商/技術參數
參數描述
MT9044AL 制造商:Microsemi Corporation 功能描述:FRAMER E1/OC3/T1 5V 44MQFP - Trays 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/OC3/T1 5V 44MQFP - Trays
MT9044AL1 制造商:Microsemi Corporation 功能描述:FRAMER E1/OC3/T1 5V 44MQFP - Trays
MT9044AP 制造商:Microsemi Corporation 功能描述:
MT9044AP1 制造商:Microsemi Corporation 功能描述:FRAMER E1/OC3/T1 5V 44PLCC - Rail/Tube 制造商:Microsemi Corporation 功能描述:T1/E1/OC3 SYSTEM SYNCHRONIZER 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC SYNCHRONIZER T1/E1 44PLCC 制造商:Microsemi Corporation 功能描述:IC SYNCHRONIZER T1/E1 44PLCC
MT9044APR1 制造商:Microsemi Corporation 功能描述:FRAMER E1/OC3/T1 5V 44PLCC - Tape and Reel 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/OC3/T1 5V 44PLCC - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*