- 您現在的位置：買賣IC網 > PDF目錄383644 > MT9044 (Mitel Networks Corporation) T1/E1/OC3 System Synchronizer(T1/E1/OC3 系統同步裝置（由一個數字鎖相環組成）) PDF資料下載
參數資料
| 型號： | MT9044 |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | T1/E1/OC3 System Synchronizer(T1/E1/OC3 系統同步裝置（由一個數字鎖相環組成）) |
| 中文描述： | T1/E1/OC3系統同步器（T1/E1/OC3系統同步裝置（由一個數字鎖相環組成）） |
| 文件頁數： | 14/34頁 |
| 文件大?。?/td> | 150K |
| 代理商： | MT9044 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
MT9044
14
the storage value is determined while the device is in
Normal Mode and locked to an external reference
signal.
The absolute Master Clock (OSCi) accuracy of the
MT9044 does not affect Holdover accuracy, but the
change in OSCi accuracy while in Holdover Mode
does.
Capture Range
Also referred to as pull-in range. This is the input
frequency range over which the synchronizer must
be able to pull into synchronization. The MT9044
capture range is equal to
±
230ppm minus the
accuracy of the master clock (OSCi). For example, a
±
32ppm master clock results in a capture range of
±
198ppm.
Lock Range
This is the input frequency range over which the
synchronizer
must
be
synchronization. The lock range is equal to the
capture range for the MT9044.
able
to
maintain
Phase Slope
Phase slope is measured in seconds per second and
is the rate at which a given signal changes phase
with respect to an ideal signal. The given signal is
typically the output signal. The ideal signal is of
constant frequency and is nominally equal to the
value of the final output signal or final input signal.
Time Interval Error (TIE)
TIE is the time delay between a given timing signal
and an ideal timing signal.
Maximum Time Interval Error (MTIE)
MTIE is the maximum peak to peak delay between a
given timing signal and an ideal timing signal within a
particular observation period.
Phase Continuity
Phase continuity is the phase difference between a
given timing signal and an ideal timing signal at the
end of a particular observation period. Usually, the
given timing signal and the ideal timing signal are of
the same frequency. Phase continuity applies to the
output of the synchronizer after a signal disturbance
due to a reference switch or a mode change. The
observation period is usually the time from the
disturbance, to just after the synchronizer has settled
to a steady state.
In the case of the MT9044, the output signal phase
continuity is maintained to within
±
5ns at the
instance (over one frame) of all reference switches
and all mode changes. The total phase shift,
depending on the switch or type of mode change,
may accumulate up to
±
200ns over many frames.
The rate of change of the
±
200ns phase shift is
limited to a maximum phase slope of approximately
5ns/125us. This meets the maximum phase slope
requirement
of
Bellcore
1.326ms).
GR-1244-CORE
(81ns/
Phase Lock Time
This is the time it takes the synchronizer to phase
lock to the input signal. Phase lock occurs when the
input signal and output signal are not changing in
phase with respect to each other (not including jitter).
Lock time is very difficult to determine because it is
affected by many factors which include:
i) initial input to output phase difference
ii) initial input to output frequency difference
iii) synchronizer loop filter
iv) synchronizer limiter
Although a short lock time is desirable, it is not
always possible to achieve due to other synchronizer
requirements. For instance, better jitter transfer
performance is achieved with a lower frequency loop
filter which increases lock time. And better (smaller)
phase slope performance (limiter) results in longer
lock times. The MT9044 loop filter and limiter were
optimized to meet the AT&T TR62411 jitter transfer
and phase slope requirements. Consequently, phase
lock time, which is not a standards requirement, may
be longer than in other applications. See AC
Electrical
Characteristics
maximum phase lock time.
-
Performance
for
MTIE S
TIEmax t
( )
TIEmin t
( )
–
=
相關PDF資料 |
PDF描述 |
|---|---|
| MT90500 | Multi-Channel ATM AAL1 SAR(多通道 ATM AAL1分段及重組設備（基于通訊總線的系統與ATM網絡的接口）) |
| MT90500 | Multi-Channel ATM AAL1 SAR |
| MT90500AL | Multi-Channel ATM AAL1 SAR |
| MT90502 | Multi-Channel AAL2 SAR(多通道 ATM AAL2分段及重組設備（基于通訊總線的系統與ATM網絡的接口）) |
| MT90732AP | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT9044AL | 制造商:Microsemi Corporation 功能描述:FRAMER E1/OC3/T1 5V 44MQFP - Trays 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/OC3/T1 5V 44MQFP - Trays |
| MT9044AL1 | 制造商:Microsemi Corporation 功能描述:FRAMER E1/OC3/T1 5V 44MQFP - Trays |
| MT9044AP | 制造商:Microsemi Corporation 功能描述: |
| MT9044AP1 | 制造商:Microsemi Corporation 功能描述:FRAMER E1/OC3/T1 5V 44PLCC - Rail/Tube 制造商:Microsemi Corporation 功能描述:T1/E1/OC3 SYSTEM SYNCHRONIZER 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC SYNCHRONIZER T1/E1 44PLCC 制造商:Microsemi Corporation 功能描述:IC SYNCHRONIZER T1/E1 44PLCC |
| MT9044APR1 | 制造商:Microsemi Corporation 功能描述:FRAMER E1/OC3/T1 5V 44PLCC - Tape and Reel 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/OC3/T1 5V 44PLCC - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。