參數資料
型號： MSC1200Y3PFBT
廠商： TEXAS INSTRUMENTS INC
元件分類： 微控制器/微處理器
英文描述： 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQFP48
封裝： GREEN, PLASTIC, TQFP-48
文件頁數： 24/93頁
文件大?。?/td> 1093K
代理商： MSC1200Y3PFBT
MSC1200
MSC1201
MSC1202
SBAS317E APRIL 2004 REVISED MAY 2006
www.ti.com
30
SPI
The MSC120x implement a basic SPI interface that
includes the hardware for simple serial data transfers.
Figure 17 shows a block diagram of the SPI. The
peripheral supports master and slave modes, full duplex
data transfers, both clock polarities, both clock phases, bit
order, and slave select.
The timing diagram for supported SPI data transfers is
shown in Figure 18.
The I/O pins needed for data transfer are Data In (DIN),
Data Out (DOUT) and serial clock (SCK). The slave select
(SS) pin can also be used to control the output of data on
DOUT.
The DIN pin is used for shifting data in for both master and
slave modes.
The DOUT pin is used for shifting data out for both master
and slave modes.
The SCK pin is used to synchronize the transfer of data for
both master and slave modes. SCK is always generated
by the master. The generation of SCK in master mode can
be done either in software (by simply toggling the port pin),
or by configuring the output on the SCK pin via PASEL
(SFR F2h). A list of the most common methods of
generating SCK follows, but the complete list of clock
sources can be found by referring to the PASEL SFR.
D Toggle SCK by setting and clearing the port pin.
D Memory Write Pulse (WR) that is idle high.
Whenever an external memory write command
(MOVX) is executed, a pulse is seen on P3.6. This
method can be used only if CPOL is set to ‘1’.
D Memory Write Pulse toggle version. In this mode,
SCK toggles whenever an external write command
(MOVX) is executed.
D T0_Out signal can be used as a clock. A pulse is
generated on SCK whenever Timer 0 expires. The
idle state of the signal is low, so this can be used
only if CPOL is cleared to ‘0’.
D T0_Out toggle. SCK toggles whenever Timer 0
expires.
D T1_Out signal can be used as a clock. A pulse is
generated whenever Timer 1 expires. The idle state
of the signal is low, so this can be used only if CPOL
is cleared to ‘0’.
D T1_Out toggle. SCK toggles whenever Timer 1
expires.
SPI /I2C
Data Write
SPICON
I2CCON
I2C
Stretch
Control
Counter
Start/Stop
Detect
SPI /I2C
Data Read
Pad Control
DOUT
P1.2
P1.4
P3.6
P1.3
Logic
DOUT
TX_CLK
RX_CLK
SS
SCK/SCL
CNT_CLK
CNT INT
I2C INT
DIN
CLKS (refer to PASEL, SFR F2h)
SS
SCK
DIN
Figure 17. SPI/I2C Block Diagram
相關PDF資料
PDF描述
MSC1201Y2RHHR 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQCC36
MSC1202Y3RHHT 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQCC36
MSC1202Y2RHHT 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQCC36
MSC1202Y3RHHRG4 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQCC36
MSC1201Y3RHHR 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQCC36
相關代理商/技術參數
參數描述
MSC1200Y3PFBTG4 功能描述:模數轉換器 - ADC Precision ADC & DAC w/8051 CPU & Flash RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MSC1201 制造商:BB 制造商全稱:BB 功能描述:Precision, Analog-to-Digital Converter (ADC) and Digital-to-Analog Converter (DAC) with 8051 Microcontroller and Flash Memory
MSC1201EVM 功能描述:數據轉換 IC 開發工具 MSC1201EVM Eval Mod RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
MSC1201-XX 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:60-Bit VFD Tube Driver with Digital Dimming and PWM Conversion Function
MSC1201Y2 制造商:BB 制造商全稱:BB 功能描述:Precision, Analog-to-Digital Converter (ADC) and Digital-to-Analog Converter (DAC) with 8051 Microcontroller and Flash Memory
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*