參數資料
型號： MR80C52XXX-25SHXXX:R
廠商： ATMEL CORP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQCC44
封裝： LCC-44
文件頁數： 104/176頁
文件大小： 4226K
33
8126F–AVR–05/12
ATtiny13A
7.4.6
Port Pins
When entering a sleep mode, all port pins should be configured to use minimum power. The
most important thing is then to ensure that no pins drive resistive loads. In sleep modes where
both the I/O clock (clk
I/O) and the ADC clock (clkADC) are stopped, the input buffers of the device
will be disabled. This ensures that no power is consumed by the input logic when not needed. In
some cases, the input logic is needed for detecting wake-up conditions, and it will then be
enabled. Refer to the section “Digital Input Enable and Sleep Modes” on page 53 for details on
which pins are enabled. If the input buffer is enabled and the input signal is left floating or has an
analog signal level close to V
CC/2, the input buffer will use excessive power.
For analog input pins, the digital input buffer should be disabled at all times. An analog signal
level close to V
CC/2 on an input pin can cause significant current even in active mode. Digital
input buffers can be disabled by writing to the Digital Input Disable Register (DIDR0). Refer to
7.5
Register Description
7.5.1
BODCR – Brown-Out Detector Control Register
The BOD Control Register contains control bits for disabling the BOD by software.
Bit 1 – BODS: BOD Sleep
In order to disable BOD during sleep the BODS bit must be written to logic one. This is controlled
by a timed sequence and the enable bit, BODSE. First, both BODS and BODSE must be set to
one. Second, within four clock cycles, BODS must be set to one and BODSE must be set to
zero. The BODS bit is active three clock cycles after it is set. A sleep instruction must be exe-
cuted while BODS is active in order to turn off the BOD for the actual sleep mode. The BODS bit
is automatically cleared after three clock cycles.
Bit 0 – BODSE: BOD Sleep Enable
The BODSE bit enables setting of BODS control bit, as explained on BODS bit description. BOD
disable is controlled by a timed sequence.
7.5.2
MCUCR – MCU Control Register
The MCU Control Register contains control bits for power management.
Bit 5 – SE: Sleep Enable
The SE bit must be written to logic one to make the MCU enter the sleep mode when the SLEEP
instruction is executed. To avoid the MCU entering the sleep mode unless it is the programmer’s
purpose, it is recommended to write the Sleep Enable (SE) bit to one just before the execution of
the SLEEP instruction and to clear it immediately after waking up.
Bit
7
654
32
10
–
BODS
BODSE
BODCR
Read/Write
RR
R/W
Initial Value
0
Bit
7
654
32
10
–
PUD
SE
SM1
SM0
–
ISC01
ISC00
MCUCR
Read/Write
R
R/W
R
R/W
Initial Value
0
相關PDF資料
PDF描述
MR80C32E-36SB 8-BIT, 36 MHz, MICROCONTROLLER, CQCC44
R80C52CXXX-25SHXXX:RD 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQCC44
MR80C52XXX-L:R 8-BIT, MROM, 12 MHz, MICROCONTROLLER, CQCC44
IS80C52FXXXS:R 8-BIT, MROM, 20 MHz, MICROCONTROLLER, PQCC44
IJ80C52FXXXS 8-BIT, MROM, 20 MHz, MICROCONTROLLER, CQCC44
相關代理商/技術參數
參數描述
MR80C86 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CMOS 16-Bit Microprocessor
MR80C86/B 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Harris Corporation 功能描述:Microprocessor, 16 Bit, 44 Pin, Ceramic, LCC
MR80C86-2 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CMOS 16-Bit Microprocessor
MR80C86-2/883 制造商:Rochester Electronics LLC 功能描述:- Bulk
MR80C86-2/B 制造商:Intersil Corporation 功能描述:MPU 80C86 16BIT CMOS 8MHZ 44PLCC - Rail/Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*