參數資料
型號： MPC8379E-RDB
廠商： Freescale Semiconductor
文件頁數： 16/117頁
文件大?。?/td> 0K
描述： BOARD REFERENCE FOR MPC837
標準包裝： 1
系列： PowerQUICC II™ PRO
類型： MPU
適用于相關產品： MPC8379
所含物品： 板
MPC8379E PowerQUICC II Pro Processor Hardware Specifications, Rev. 8
112
Freescale Semiconductor
The value of this resistance and the strength of the driver’s current source can be found by making two
measurements. First, the output voltage is measured while driving logic 1 without an external differential
termination resistor. The measured voltage is V1 = Rsource × Isource. Second, the output voltage is measured
while driving logic 1 with an external precision differential termination resistor of value Rterm. The
measured voltage is V2 =(1/(1/R1 +1/R2)) × Isource. Solving for the output impedance gives Rsource =
Rterm × (V1/V2 – 1). The drive current is then Isource =V1/Rsource.
This table summarizes the signal impedance targets. The driver impedance are targeted at minimum VDD,
nominal OVDD, 105°C.
24.5
Configuration Pin Muxing
The device provides the user with power-on configuration options which can be set through the use of
external pull-up or pull-down resistors of 4.7 k
Ω on certain output pins (see customer visible configuration
pins). These pins are generally used as output only pins in normal operation.
While HRESET is asserted however, these pins are treated as inputs. The value presented on these pins
while HRESET is asserted, is latched when PORESET deasserts, at which time the input receiver is
disabled and the I/O circuit takes on its normal function. Careful board layout with stubless connections
to these pull-up/pull-down resistors coupled with the large value of the pull-up/pull-down resistor should
minimize the disruption of signal quality or speed for output pins thus configured.
24.6
Pull-Up Resistor Requirements
The device requires high resistance pull-up resistors (10 k
Ω is recommended) on open drain type pins
including I2C pins and IPIC interrupt pins.
For more information on required pull-up resistors and the connections required for the JTAG interface,
see AN3665, “MPC837xE Design Checklist.”
25 Ordering Information
Ordering information for the parts fully covered by this specification document is provided in
Table 80. Impedance Characteristics
Impedance
Local Bus, Ethernet,
DUART, Control,
Configuration, Power
Management
PCI Signals
(not including PCI
output clocks)
PCI Output Clocks
(including
PCI_SYNC_OUT)
DDR DRAM
Symbol
Unit
RN
42 Target
25 Target
42 Target
20 Target
Z0
W
RP
42 Target
25 Target
42 Target
20 Target
Z0
W
Differential
NA
ZDIFF
W
Note: Nominal supply voltages. See Table 2, Tj = 105°C.
相關PDF資料
PDF描述
MPC8379E-MDS-PB BOARD PROCESSOR FOR MDS S
MPC8378E-MDS-PB BOARD PROCESSOR FOR MDS S
MPC5553EVBE BOARD EVAL FOR MPC5553
MPC8323E-MDS-PB BOARD MODULE DEV SYSTEM 8323
MPC5534EVBE BOARD EVAL FOR MPC5534
相關代理商/技術參數
參數描述
MPC8379E-RDBA 功能描述:開發板和工具包 - 其他處理器 MPC8379E REF DESIGN BD RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓:
MPC8379E-RDBA 制造商:Freescale Semiconductor 功能描述:MPC8379E-RDB Reference Platform
MPC8379EVRAFDA 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:PowerQUICC? II Pro Processor Hardware Specifications
MPC8379EVRAFFA 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:PowerQUICC? II Pro Processor Hardware Specifications
MPC8379EVRAFGA 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:PowerQUICC? II Pro Processor Hardware Specifications
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*