參數資料
型號: MPC823UM_REV1_16-CPM7
廠商: Motorola, Inc.
英文描述: 10 AMP SUBMINIATURE POWER RELAY
中文描述: 通信處理器模塊
文件頁數: 27/74頁
文件大?。?/td> 234K
代理商: MPC823UM_REV1_16-CPM7
Communication Processor Module
MOTOROLA
MPC823 REFERENCE MANUAL
16-405
S
C
1
P
12.Initialize the RX buffer descriptor. Assume the RX data buffer is at 0x00001000 in main
memory. Write 0xB000 to RX_BD_Status, 0x0000 to RX_BD_Length (not required),
and 0x00001000 to RX_BD_Pointer.
13.Initialize the TX buffer descriptor. Assume the TX data buffer is at 0x00002000 in main
memory and contains five 8-bit characters. Then write 0xB000 to TX_BD_Status,
0x0005 to TX_BD_Length, and 0x00002000 to TX_BD_Pointer.
14.Write 0xFF to the SMCE–UART register to clear any previous events.
15.Write 0x17 to the SMCM–UART register to enable all possible serial management
controller interrupts.
16.Write 0x00000010 to the CIMR so SMC1 can generate a system interrupt. The CICR
must also be initialized.
17.Write 0x4820 to SMCMR to configure normal operation (not loopback), 8-bit
characters, no parity, 1 stop bit. Notice that the transmitter and receiver are not
enabled yet.
18.Write 0x4823 to SMCMR to enable the SMC1 transmitter and receiver. This additional
write ensures that the TEN and REN bits are enabled last.
16.11.6.16 HANDLING INTERRUPTS IN THE SMCx UART CONTROLLER.
Follow
these steps to handle an interrupt in a serial management controller:
1. Once an interrupt occurs, read the SMCE–UART register to discover the cause of the
interrupt. To clear the SMCE bits, write ones to them.
2. Process the TX buffer descriptor to reuse it if the TX bit is set in the SMCE–UART
register. Extract data from the RX buffer descriptor if the RX bit is set in the
SMCE–UART. To transmit another buffer, set the R bit in the TX buffer descriptor.
3. Clear the SMCx bit in the CISR.
4. Execute the
rfi
instruction.
Note:
After 5 bytes are transmitted, the TX buffer descriptor is closed. The receive
buffer is closed after 16 bytes are received. Any data received after 16 bytes
causes a busy (out-of-buffers) condition since only one RX buffer descriptor is
prepared.
相關PDF資料
PDF描述
MPC9109 LOW VOLTAGE 1:18 CLOCK DISTRIBUTION CHIP
MPC9229 400 MHz Low Voltage PECL Clock Synthesizer
MPC9230 800 MHz Low Voltage PECL Clock Synthesizer
MPC9350 LOW VOLTAGE PLL CLOCK DRIVER
MPC9350D LOW VOLTAGE PLL CLOCK DRIVER
相關代理商/技術參數
參數描述
MPC823VR66B2T 功能描述:微處理器 - MPU POWER QUICC RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MPC823VR75B2T 功能描述:微處理器 - MPU POWER QUICC RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MPC823VR81B2T 功能描述:微處理器 - MPU POWER QUICC RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MPC823ZQ66B2T 功能描述:微處理器 - MPU PORTABLE SYSTEM MPU RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MPC823ZQ75B2T 功能描述:微處理器 - MPU PORTABLE SYSTEM MPU RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324