- 您現在的位置：買賣IC網 > PDF目錄382345 > MPC823 (Motorola, Inc.) Communication Processor Module PDF資料下載
參數資料
| 型號： | MPC823 |
| 廠商： | Motorola, Inc. |
| 英文描述： | Communication Processor Module |
| 中文描述： | 通信處理器模塊 |
| 文件頁數： | 74/74頁 |
| 文件大?。?/td> | 234K |
| 代理商： | MPC823 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁當前第74頁
Communication Processor Module
16-452
MPC823 REFERENCE MANUAL
MOTOROLA
S
C
1
P
9. Write 0xFF to the SPIE register to clear any previous events.
10.Write 0x37 to the SPIM register to enable all possible serial peripheral interface
interrupts.
11.Write 0x00000020 to the CIMR to allow the serial peripheral interface to generate a
system interrupt. The CICR must also be initialized.
12.Write 0x0170 to the SPMODE register to enable normal operation (not loopback),
master mode, and 8-bit characters. The SPI baud rate generator speed is ignored
because the serial peripheral interface is in slave mode.
13.Set the STR bit in the SPCOM register to enable the serial peripheral interface to be
ready once the master begins the transfer.
16.12.7 Handling Interrupts in the SPI
The following sequence must be followed to handle interrupts in the serial peripheral
interface.
1. Once an interrupt occurs, read the SPIE register to discover the cause of the
interrupts. Normally, the SPIE bits must be cleared at this time.
2. Process the TX buffer descriptor to reuse it and the RX buffer descriptor to extract the
data from it. To transmit another buffer, simply set the R bit of the TX buffer descriptor,
the E bit of the RX buffer descriptor, and the STR bit of the SPCOM register.
3. Clear the SPI bit in the CISR.
4. Execute the
rfi
instruction.
Note:
If the master transmits 3 bytes and negates the SPISEL pin, the RX buffer
descriptor is closed, but the TX buffer descriptor remains open. If the master
transmits 5 or more bytes, the TX buffer descriptor is closed after the fifth byte.
If the master transmits 16 bytes and negates the SPISEL pin, the RX buffer
descriptor is closed with no errors and no out-of-buffer error occurs. If the master
transmits more than 16 bytes, the RX buffer descriptor is closed (completely full)
and the out-of-buffer error occurs after the 17th byte is received.
相關PDF資料 |
PDF描述 |
|---|---|
| MPC823UM_REV1_16-CPM7 | 10 AMP SUBMINIATURE POWER RELAY |
| MPC9109 | LOW VOLTAGE 1:18 CLOCK DISTRIBUTION CHIP |
| MPC9229 | 400 MHz Low Voltage PECL Clock Synthesizer |
| MPC9230 | 800 MHz Low Voltage PECL Clock Synthesizer |
| MPC9350 | LOW VOLTAGE PLL CLOCK DRIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPC823CVR66B2T | 功能描述:微處理器 - MPU POWER QUICC RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| MPC823CZQ66B2T | 功能描述:微處理器 - MPU PORTABLE SYSTEM MPU RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| MPC823CZQ66B2T | 制造商:Freescale Semiconductor 功能描述:IC 32-BIT MPU 66MHZ 256-PBGA |
| MPC823ELD | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:MPC823e Mobile Computing Microprocessor |
| MPC823ELE | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:MPC823e Mobile Computing Microprocessor |
發布緊急采購，3分鐘左右您將得到回復。