參數資料
型號： MPC823
廠商： Motorola, Inc.
英文描述： Communication Processor Module
中文描述： 通信處理器模塊
文件頁數： 67/74頁
文件大小： 234K
代理商： MPC823
Communication Processor Module
MOTOROLA
MPC823 REFERENCE MANUAL
16-445
S
C
1
P
W—Wrap (Final Buffer Descriptor in Table)
0 = This is not the last buffer descriptor in the RX buffer descriptor table.
1 = This is the last buffer descriptor in the RX buffer descriptor table. After this buffer
is used, the communication processor module receives incoming data into the first
buffer descriptor that RBASE points to in the table. The number of RX buffer
descriptors in this table is programmable and determined only by the W bit and
overall space constraints of the dual-port RAM.
I—Interrupt
0
1
No interrupt is generated after this buffer is filled.
The RXB bit in the SPIE register is set when this buffer is completely filled by the
communication processor module, indicating the need for the core to process the
buffer. The RXB bit can cause an interrupt if it is enabled.
CM—Continuous Mode
This bit is valid only when the serial peripheral interface is in master mode. In slave mode,
it must be written as a zero.
0 = Normal operation.
1 = The E bit is not cleared by the communication processor module after this buffer
descriptor is closed, thus allowing the associated data buffer to be automatically
overwritten next time the communication processor module accesses this buffer
descriptor. This allows continuous reception from an SPI slave into one buffer for
autoscanning of a serial A/D peripheral with no core overhead.
L—Last
This bit is set by the serial peripheral interface when the buffer is closed because the
SPISEL pin was negated. This only occurs when the serial peripheral interface is in slave
mode. Otherwise, the ME bit is set. The serial peripheral interface writes this bit after the
received data is placed into the associated data buffer.
0 = This buffer does not contain the last character of the message.
1 = This buffer contains the last character of the message.
OV—Overrun
This bit indicates that a receiver overrun has occurred during reception. This can only occur
when the serial peripheral interface is in slave mode. The serial peripheral interface writes
this bit after the received data is placed into the associated data buffer.
ME—Multimaster Error
This bit indicates that this buffer is closed because the SPISEL pin was asserted when the
serial peripheral interface was in master mode. This indicates a synchronization problem
between multiple masters on the SPI bus. The serial peripheral interface writes this bit after
the received data is placed into the associated data buffer.
相關PDF資料
PDF描述
MPC823UM_REV1_16-CPM7 10 AMP SUBMINIATURE POWER RELAY
MPC9109 LOW VOLTAGE 1:18 CLOCK DISTRIBUTION CHIP
MPC9229 400 MHz Low Voltage PECL Clock Synthesizer
MPC9230 800 MHz Low Voltage PECL Clock Synthesizer
MPC9350 LOW VOLTAGE PLL CLOCK DRIVER
相關代理商/技術參數
參數描述
MPC823CVR66B2T 功能描述:微處理器 - MPU POWER QUICC RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MPC823CZQ66B2T 功能描述:微處理器 - MPU PORTABLE SYSTEM MPU RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MPC823CZQ66B2T 制造商:Freescale Semiconductor 功能描述:IC 32-BIT MPU 66MHZ 256-PBGA
MPC823ELD 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:MPC823e Mobile Computing Microprocessor
MPC823ELE 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:MPC823e Mobile Computing Microprocessor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*