- 您現在的位置：買賣IC網 > PDF目錄98023 > MK2069-04GITR 160 MHz, OTHER CLOCK GENERATOR, PDSO56 PDF資料下載
參數資料
| 型號： | MK2069-04GITR |
| 元件分類： | 時鐘產生/分配 |
| 英文描述： | 160 MHz, OTHER CLOCK GENERATOR, PDSO56 |
| 封裝： | 6.10 MM, 0.50 MM PITCH, TSSOP-56 |
| 文件頁數： | 17/19頁 |
| 文件大?。?/td> | 449K |
| 代理商： | MK2069-04GITR |
VCXO-Based Universal Clock Translator
MDS 2069-04 G
7
Revision 090905
Integr ated Circuit System s l 525 Ra ce Stree t , Sa n Jose, CA 951 26 l te l (4 08) 297 -1 201 l
MK2069-04
CP establishes a second pole in the VCXO PLL loop
filter. For higher damping factors (> 1), calculate the
value of CP based on a CS value that would be used for
a damping factor of 1. This will minimize baseband
peaking and loop instability that can lead to output jitter.
CP also dampens VCXO input voltage modulation by
the charge pump correction pulses. A CP value that is
too low will result in increased output phase noise at
the phase detector frequency due to this. In extreme
cases where input jitter is high, charge pump current is
high, and CP is too small, the VCXO input voltage can
hit the supply or ground rail resulting in non-linear loop
response.
The best way to set the value of CP is to use the filter
response software available from ICS (please refer to
the following section). CP should be increased in value
until it just starts affecting the passband peak.
Loop Filter Response Software
Online tools to calculate loop filter response can be
found at www.icst.com.
Graph of Charge Pump Current vs. Value of RSET (external resistor)
Charge Pump Current, Example Settings
from Above Graph
Setting Charge Pump Current
The recommended range for the charge pump current
is 25 A to 300 A. Below 25 A, loop filter charge
leakage, due to PCB or capacitor leakage, can become
a problem. This loop filter leakage can cause locking
problems, output clock cycle slips, or low frequency
phase noise.
As can be seen in the loop bandwidth and damping
factor equations or by using the filter response software
available from ICS, increasing charge pump current
(ICP) increases both bandwidth and damping factor.
10E-6
100E-6
1E-3
100E+3
1E+6
10E+6
RSET, ohms
I CP
,A
m
ps
Recommended Range
of Operation
RSET
Charge Pump Current
(ICP)
5 M
25
A
3 M
42
A
2 M
65
A
1 M
125
A
480 k
255
A
400 k
300
A
相關PDF資料 |
PDF描述 |
|---|---|
| MK20DN512ZVMB10 | 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PBGA81 |
| MK20DX256ZVLK10R | 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PQFP80 |
| MK20DX256ZVMB10R | 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PBGA81 |
| MK20DN512ZVMB10R | 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PBGA81 |
| MK30DN512ZVMC10 | RISC MICROCONTROLLER, PBGA121 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MK206N 454634/1/MK | 制造商:NSF (CONTROLS) 功能描述:WAFER MK 2POLE 6 POS 制造商:NSF (CONTROLS) 功能描述:WAFER, MK, 2POLE, 6 POS 制造商:NSF (CONTROLS) 功能描述:WAFER, MK, 2POLE, 6 POS; For Use With:Rotary Switches; No. of Poles:2; No. of Positions:6; SVHC:No SVHC (19-Dec-2012); Contact Current @ Contact Voltage AC Max:500mA; Contact Current AC Max:5A; Contact Current DC Max:5A; Contact ;RoHS Compliant: Yes |
| MK206S 454634MK | 制造商:NSF (CONTROLS) 功能描述:WAFER MK 2POLE 6 POS 制造商:NSF (CONTROLS) 功能描述:WAFER, MK, 2POLE, 6 POS 制造商:NSF (CONTROLS) 功能描述:WAFER, MK, 2POLE, 6 POS; No. of Poles:2; No. of Positions:6; SVHC:No SVHC (19-Dec-2012); Contact Current @ Contact Voltage AC Max:500mA; Contact Current AC Max:5A; Contact Current DC Max:5A; Contact Current Rating:5A; Contact ;RoHS Compliant: Yes |
| MK20-B-100W | 功能描述:近程傳感器 1 Form A Cylindrical Term. RoHS:否 制造商:Vishay Semiconductors 感應方式:Optical 感應距離:1 mm to 200 mm 電源電壓:2.5 V to 3.6 V 安裝風格:SMD/SMT 輸出配置:Digital 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 系列:VCNL3020 |
| MK20-B-100W_DE | 制造商:MEDER 制造商全稱:Meder Electronic 功能描述:(deutsch) MK Reed Sensor |
| MK20-B-500W | 制造商:MEDER 制造商全稱:Meder Electronic 功能描述:MK Reed Sensor |
發布緊急采購，3分鐘左右您將得到回復。